root@debian:~# shutdown -r now
Broadcast message from root@debian
(/dev/ttyS0) at 15:00 ...
The system is going down for reboot NOW!
* Saving the system clock
* Asking all remaining processes to terminate... [ OK ]
* All processes ended within 2 seconds.... [ OK ]
* Deconfiguring network interfaces... [ OK ]
* Unmounting temporary filesystems... [ OK ]
* Deactivating swap... [ OK ]
* Stopping remaining crypto disks... [ OK ]
* Stopping early crypto disks... [ OK ]
* Will now restart
Restarting system.
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__|
** MARVELL BOARD: SHEEVA PLUG LE
U-Boot 1.1.4 (Mar 19 2009 - 16:06:59) Marvell version: 3.4.16
U-Boot code: 00600000 -> 0067FFF0 BSS: -> 006CEE80
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz
DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
Flash: 0 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Hit any key to stop autoboot: 0
NAND read: device 0 offset 0x100000, size 0x400000
Reading data from 0x4ff800 -- 100% complete.
4194304 bytes read: OK
## Booting image at 00800000 ...
Image Name: Linux-2.6.22.18
Created: 2009-03-19 9:18:16 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2106696 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux.................................................................................................................................... done, booting the kernel.
Linux version 2.6.22.18 (dhaval@devbox) (gcc version 4.2.1) #1 Thu Mar 19 14:46:22 IST 2009
CPU: ARM926EJ-S [56251311] revision 1 (ARMv5TE), cr=00053177
Machine: Feroceon-KW
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists. Total pages: 130048
Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:0x400000@0x100000(uImage),0x1fb00000@0x500000(rootfs) rw root=/dev/mtdblock1 rw ip=10.4.50.4:10.4.50.5:10.4.50.5:255.255.255.0:DB88FXX81:eth0:none
PID hash table entries: 2048 (order: 11, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 256MB 256MB 0MB 0MB = 512MB total
Memory: 515456KB available (3864K code, 257K data, 104K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 256MB
SDRAM_CS1 ....base 10000000, size 256MB
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e8000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
INTER_REGS ....base f1000000, size 1MB
NFLASH_CS ....base fa000000, size 2MB
SPI_CS ....base f4000000, size 16MB
BOOT_ROM_CS ....no such
DEV_BOOTCS ....no such
CRYPT_ENG ....base f0000000, size 2MB
Marvell Development Board (LSP Version KW_LSP_4.2.7_patch2)-- SHEEVA PLUG Soc: 88F6281 A0 LE
Detected Tclk 200000000 and SysClk 400000000
MV Buttons Device Load
Marvell USB EHCI Host controller #0: c08b8600
PEX0 interface detected no Link.
PCI: bus0: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
Time: kw_clocksource clocksource has been installed.
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
TCP established hash table entries: 65536 (order: 7, 524288 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 65536 bind 65536)
TCP reno registered
RTC registered
Use the XOR engines (acceleration) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
Number of XOR engines to use: 4
cesadev_init(c000c894)
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Warning: TS unit is powered off.
MV Buttons Driver Load
NTFS driver 2.1.28 [Flags: R/O].
JFFS2 version 2.2. (NAND) 誕 ・001-2006 Red Hat, Inc.
io scheduler noop registered
io scheduler anticipatory registered (default)
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
serial8250.0: ttyS1 at MMIO 0xf1012100 (irq = 34) is a 16550A
Loading Marvell Ethernet Driver:
o Cached descriptors in DRAM
o DRAM SW cache-coherency
o Single RX Queue support - ETH_DEF_RXQ=0
o Single TX Queue support - ETH_DEF_TXQ=0
o TCP segmentation offload enabled
o Receive checksum offload enabled
o Transmit checksum offload enabled
o Network Fast Processing (Routing) supported
o Driver ERROR statistics enabled
o Driver INFO statistics enabled
o Proc tool API enabled
o Rx descripors: q0=128
o Tx descripors: q0=532
o Loading network interface(s):
o eth0, ifindex = 1, GbE port = 0
o eth1, ifindex = 2, GbE port = 1
mvFpRuleDb (dfd00000): 16384 entries, 65536 bytes
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e100: Intel(R) PRO/100 Network Driver, 3.5.17-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
Warning Sata is Powered Off
NFTL driver: nftlcore.c $Revision: 1.98 $, nftlmount.c $Revision: 1.41 $
NAND device: Manufacturer ID: 0xad, Chip ID: 0xdc (Hynix NAND 512MiB 3,3V 8-bit)
Scanning device for bad blocks
Bad eraseblock 274 at 0x02240000
Bad eraseblock 627 at 0x04e60000
Bad eraseblock 663 at 0x052e0000
Bad eraseblock 976 at 0x07a00000
Bad eraseblock 1552 at 0x0c200000
Bad eraseblock 1657 at 0x0cf20000
Bad eraseblock 1658 at 0x0cf40000
Bad eraseblock 2404 at 0x12c80000
Bad eraseblock 2470 at 0x134c0000
Bad eraseblock 2514 at 0x13a40000
Bad eraseblock 2688 at 0x15000000
Bad eraseblock 2690 at 0x15040000
Bad eraseblock 2707 at 0x15260000
Bad eraseblock 2728 at 0x15500000
Bad eraseblock 2771 at 0x15a60000
Bad eraseblock 2781 at 0x15ba0000
Bad eraseblock 3039 at 0x17be0000
Bad eraseblock 3469 at 0x1b1a0000
2 cmdlinepart partitions found on MTD device nand_mtd
Using command line partition definition
Creating 2 MTD partitions on "nand_mtd":
0x00100000-0x00500000 : "uImage"
0x00500000-0x20000000 : "rootfs"
ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v3.0
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Linux telephony interface: v1.00
Marvell Telephony Driver:
mvBoardVoiceAssembleModeGet: TDM not supported(boardId=0x9)
assembly=-1,irq=-1
mp_check_config: Error, invalid voice assembley mode
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1 97 MB/s
raid6: int32x2 114 MB/s
raid6: int32x4 122 MB/s
raid6: int32x8 110 MB/s
raid6: using algorithm int32x4 (122 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
arm4regs : 1084.000 MB/sec
8regs : 754.800 MB/sec
32regs : 899.600 MB/sec
raid5: using function: arm4regs (1084.000 MB/sec)
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
dm_crypt using the OCF package.
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
mvsdmmc: irq =28 start f1090000
mvsdmmc: no IRQ detect
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Advanced Linux Sound Architecture Driver Version 1.0.14 (Thu May 31 09:03:25 2007 UTC).
mvCLAudioCodecRegGet: Error while reading register!
mvCLAudioCodecInit: Error - Invalid Cirrus Logic chip/rev ID!
Error - Cannot initialize audio decoder.at address =0xff<6>ALSA device list:
#0: Marvell mv88fx_snd ALSA driver
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
eth0: started
IP-Config: Complete:
device=eth0, addr=10.4.50.4, mask=255.255.255.0, gw=10.4.50.5,
host=DB88FXX81, domain=, nis-domain=(none),
bootserver=10.4.50.5, rootserver=10.4.50.5, rootpath=
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Empty flash at 0x0d816ce4 ends at 0x0d817000
Empty flash at 0x1a19c1a0 ends at 0x1a19c800
VFS: Mounted root (jffs2 filesystem).
Freeing init memory: 104K
* Setting preliminary keymap... [ OK ]
* Setting the system clock
* Starting basic networking... [ OK ]
* Starting kernel event manager... [ OK ]
* Loading hardware drivers... [ OK ]
* Setting the system clock
* Loading kernel modules... * Loading manual drivers... [ OK ]
* Setting kernel variables (/etc/sysctl.conf)... [ OK ]
* Setting kernel variables (/etc/sysctl.d/10-console-messages.conf)... [ OK ]
* Setting kernel variables (/etc/sysctl.d/10-network-security.conf)... [ OK ]
* Setting kernel variables (/etc/sysctl.d/10-process-security.conf)... error: "vm.mmap_min_addr" is an unknown key
[fail]
* Setting kernel variables (/etc/sysctl.d/10-tcp-timestamps-workaround.conf)... [ OK ]
* Activating swap... [ OK ]
FATAL: Could not load /lib/modules/2.6.22.18/modules.dep: No such file or directory
FATAL: Could not load /lib/modules/2.6.22.18/modules.dep: No such file or directory
* Starting early crypto disks... [ OK ]
FATAL: Could not load /lib/modules/2.6.22.18/modules.dep: No such file or directory
FATAL: Could not load /lib/modules/2.6.22.18/modules.dep: No such file or directory
* Starting remaining crypto disks... [ OK ]
* Checking file systems... fsck 1.41.3 (12-Oct-2008)
[ OK ]
* Mounting local filesystems... [ OK ]
* Activating swapfile swap... [ OK ]
* Configuring network interfaces... [ OK ]
* Setting up console font and keymap... [ OK ]
* Starting system log daemon...
Ubuntu jaunty (development branch) debian ttyS0
debian login: [ OK ]
* Starting kernel log daemon... [ OK ]
* Starting OpenBSD Secure Shell server sshd [ OK ]
* Starting periodic command scheduler crond [ OK ]
fat: exports duplicate symbol fat_add_entries (owned by kernel)
insmod: error inserting '/boot/fat.ko': -1 Invalid module format
Ubuntu jaunty (development branch) debian ttyS0
debian login:
|
←（前のページ） ログイン |
当月のハックの記録 SheevaPlug/玄柴(KURO-SHEEVA)をハックしよう トップ |
（次のページ）→ ウサギが先か、カメが先か |