カーネルをリコンフィグして、
WLI-UC-GNM2 を認識するようになったので、
設定を進める。。。
ってどこから進めれば良いの?
まずは、状態を見るところから。
yasunari@qvl:~$ sudo ifconfig -a eth1 Link encap:Ethernet HWaddr 4c:e6:76:e7:0f:42 inet addr:192.168.2.56 Bcast:192.168.2.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5519 errors:0 dropped:0 overruns:0 frame:0 TX packets:2396 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:532 RX bytes:642306 (627.2 KiB) TX bytes:330380 (322.6 KiB) Interrupt:11 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:4 errors:0 dropped:0 overruns:0 frame:0 TX packets:4 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:200 (200.0 B) TX bytes:200 (200.0 B) wlan0 Link encap:Ethernet HWaddr 10:6f:3f:89:e0:66 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wmaster0 Link encap:UNSPEC HWaddr 10-6F-3F-89-E0-66-00-00-00-00-00-00-00-00-00-00 [NO FLAGS] MTU:0 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) yasunari@qvl:~$wlan0 が、それらしい。
yasunari@qvl:~$ sudo apt-get install wireless-tools Reading package lists... Done Building dependency tree Reading state information... Done The following extra packages will be installed: libiw30 The following NEW packages will be installed: libiw30 wireless-tools 0 upgraded, 2 newly installed, 0 to remove and 0 not upgraded. Need to get 169 kB of archives. After this operation, 524 kB of additional disk space will be used. Do you want to continue [Y/n]? y Get:1 http://ftp.jp.debian.org/debian/ squeeze/main libiw30 armel 30~pre9-5 [36.0 kB] Get:2 http://ftp.jp.debian.org/debian/ squeeze/main wireless-tools armel 30~pre9-5 [133 kB] Fetched 169 kB in 2s (62.7 kB/s) Selecting previously deselected package libiw30. (Reading database ... 15826 files and directories currently installed.) Unpacking libiw30 (from .../libiw30_30~pre9-5_armel.deb) ... Selecting previously deselected package wireless-tools. Unpacking wireless-tools (from .../wireless-tools_30~pre9-5_armel.deb) ... Processing triggers for man-db ... Setting up libiw30 (30~pre9-5) ... Setting up wireless-tools (30~pre9-5) ... !yasunari@qvl:~$
yasunari@qvl:~$ sudo iwconfig [sudo] password for yasunari: lo no wireless extensions. eth1 no wireless extensions. wmaster0 no wireless extensions. wlan0 IEEE 802.11bgn ESSID:"" Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated Tx-Power=0 dBm Retry long limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Management:on Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 yasunari@qvl:~$
|
← 無線 LAN アダプタの接続(3)カーネルのリコンフィグ、今度こそ |
ハックの記録 LinkStation/玄箱 をハックしよう |
→ 無線 LAN アダプタの接続(5)設定 |
Copyright (C) 2003-2012 Yasunari Yamashita. All Rights Reserved.
yasunari @ yamasita.jp 山下康成@京都府向日市