廃品回収リベンジ（９）LS-QVL でフォーマット

md でフォーマットできそうなのは、LS-QVL なのだが、、、 2.5"HDD はカートリッジにセットできないので、、、

LS-QVL にセットしてフォーマット

スロット４にセット

標準ファームで起動

フォーマット

LS-SL に戻して起動

Orion1   CPU =  Low

Checking DATA BUS
Checking ADDRESS BUS

> Checking hardware info ...
=== CPU-ID       : 0x00005182 ===
=== Strap status : 0x00802030 ===
=== H/W boardId  :       0x33 ===
=== boardId      :       0x1a ===
=== micon_support:        off ===
> OK.
=== BUFFALO LS-SL U-Boot. ===
 ** LOADER **
 ** BUFFALO BOARD: BUFFALO_BOARD_LS_SL LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (May 28 2009 - 11:06:21) Marvell version: 1.12.1 - TINY
U-Boot code: 00600000 -> 00639A58  BSS: -> 00641B24
Buffalo Version: 1.23-1.00

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz


USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy
buffalo_change_power_status > Read 0x44
buffalo_IsStopAtUbootStatus > MagicKey=0x44
buffalo_change_power_status > Read 0x44
buffalo_change_power_status > Read 0x44
buffalo_change_power_status > Writing 0x5c

Please Press HDD power button to continue ...
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a

Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0: OK
Model: ST9100828AS                              Firm: 3.BHD    Ser#: 5LZ1LN1M   
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 95396.2 MB = 93.1 GB (195371568 x 512)


2729768 bytes read
   Image Name:   Linux-2.6.31.8
   Created:      2012-06-08   2:07:34 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2729704 Bytes =  2.6 MB
   Load Address: 00008000
   Entry Point:  00008000

9617733 bytes read
   Image Name:   initrd
   Created:      2012-06-18   9:58:18 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9617669 Bytes =  9.2 MB
   Load Address: 00000000
   Entry Point:  00000000
** Bad partition 1 **
serch_boot_drv (194)>No kernel_file 1
** Bad partition 1 **
serch_boot_drv (249)>No init_file 1
Booting from Device 0
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
Hit any key to stop autoboot:  0

2729768 bytes read
** Bad partition 1 **
## Booting image at 00100000 ...
   Image Name:   Linux-2.6.31.8
   Created:      2012-06-08   2:07:34 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2729704 Bytes =  2.6 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
   Image Name:   initrd
   Created:      2012-06-18   9:58:18 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    9617669 Bytes =  9.2 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.23
Uncompressing Linux......................................................................................................................................................................... done, booting the kernel.

LS-SL ファームウェア 1.11 のインストール

tftp boot

LSUpdater.exe を実行

「ファームウェア更新」をクリック。今度こそ！！

がー

全然、進んでないし、、、

LS-SL 楽天市場