LS-WSGL の HDD で起動

Orion1   CPU =  Low

Checking DATA BUS
Checking ADDRESS BUS

> Checking hardware info ...
=== CPU-ID       : 0x00005182 ===
=== Strap status : 0x00802030 ===
=== H/W boardId  :       0x33 ===
=== boardId      :       0x1a ===
=== micon_support:        off ===
> OK.
=== BUFFALO LS-SL U-Boot. ===
 ** LOADER **
 ** BUFFALO BOARD: BUFFALO_BOARD_LS_SL LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (May 28 2009 - 11:06:21) Marvell version: 1.12.1 - TINY
U-Boot code: 00600000 -> 00639A58  BSS: -> 00641B24
Buffalo Version: 1.23-1.00

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz


USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy
buffalo_change_power_status > Read 0x00
buffalo_IsStopAtUbootStatus > MagicKey=0x00
buffalo_change_power_status > Read 0x00
buffalo_change_power_status > Read 0x00
buffalo_change_power_status > Writing 0x5c

Please Press HDD power button to continue ...
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a

Marvell Serial ATA Adapter
Integrated Sata device found
  Device 0: OK
Model: WDC WD2500BEVS-00UST0                    Firm: 01.01A01 Ser#:      WD-WXE508LP7200
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
  Device 1: OK
Model: WDC WD2500BEVS-00UST0                    Firm: 01.01A01 Ser#:      WD-WXE508EV3494
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)


1757604 bytes read
   Image Name:   Linux-2.6.16.16-arm1
   Created:      2008-11-10   4:33:33 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1757540 Bytes =  1.7 MB
   Load Address: 00008000
   Entry Point:  00008000

5674776 bytes read
   Image Name:   initrd
   Created:      2009-05-17   8:02:15 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5674712 Bytes =  5.4 MB
   Load Address: 00000000
   Entry Point:  00000000

1757604 bytes read
   Image Name:   Linux-2.6.16.16-arm1
   Created:      2008-11-10   4:33:33 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1757540 Bytes =  1.7 MB
   Load Address: 00008000
   Entry Point:  00008000

5674776 bytes read
   Image Name:   initrd
   Created:      2009-05-17   8:02:15 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5674712 Bytes =  5.4 MB
   Load Address: 00000000
   Entry Point:  00000000
Booting from Device 0
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
Hit any key to stop autoboot:  0

1757604 bytes read

5674776 bytes read
## Booting image at 00100000 ...
   Image Name:   Linux-2.6.16.16-arm1
   Created:      2008-11-10   4:33:33 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1757540 Bytes =  1.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
   Image Name:   initrd
   Created:      2009-05-17   8:02:15 UTC
   Image Type:   ARM Linux RAMDisk Image (gzip compressed)
   Data Size:    5674712 Bytes =  5.4 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK

Starting kernel ...

arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.23
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSWSGL_R1 ---
Uncompressing Linux................................................................................................................... done, booting the kernel.
Linux version 2.6.16.16-arm1 (root@build.dd-hot24.nas.buffalo.local) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #383 Mon Nov 10 13:33:20 JST 2008
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 200000000, Tclk = 166664740


- Warning - This LSP release was tested only with U-Boot release 1.7.3

Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.23
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110620KB available (2992K code, 553K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 19
Flash bankwidth 1, base ff800000, size 40000
BUFFALO LS_WSGL_R1 FLASH size 256[KB]

  Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_WSGL_R1

 Detected Tclk 166664740 and SysClk 200000000
Marvell USB EHCI Host controller #0: c16f5e00
Marvell USB EHCI Host controller #1: c16f5c00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
cesadev_init(c0011c44)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface ** egiga_init_module (0)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 0] **
** BUFFALO Disable Command Queuing Function [0 1] **
  Vendor: WDC       Model: WD2500BEVS-00UST  Rev: 01.0
  Type:   Direct-Access                      ANSI SCSI revision: 03
  Vendor: WDC       Model: WD2500BEVS-00UST  Rev: 01.0
  Type:   Direct-Access                      ANSI SCSI revision: 03
Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c1436ba0
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda4 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
Linux IAL (ERROR) : retry command host=1, bus=1 SCpnt = c1436ba0
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write back
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write back
 sdb: sdb1 sdb2 sdb4 < sdb5 sdb6 >
sd 1:0:0:0: Attached scsi disk sdb
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 1:0:0:0: Attached scsi generic sg1 type 0
physmap flash device: 40000 at ff800000
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
mice: PS/2 mouse device common for all mice
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
mvGppValueSet: Err. An attempt to set output value to GPP 15 in input mode.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
mvGppValueSet: Err. An attempt to set output value to GPP 2 in input mode.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.0.02 installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
---- in hackkit linuxrc ---
	:
	:
Debian GNU/Linux 5.0 mini ttyS0

mini login: BuffaloSwPollingCheck> SW_POWER_ON

Debian GNU/Linux 5.0 mini ttyS0

mini login: yasunari
Password:
Last login: Sun Jun 28 16:08:01 JST 2009 from localhost on pts/1
Linux mini 2.6.16.16-arm1 #383 Mon Nov 10 13:33:20 JST 2008 armv5tejl

The programs included with the Debian GNU/Linux system are free software;
the exact distribution terms for each program are described in the
individual files in /usr/share/doc/*/copyright.

Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent
permitted by applicable law.
yasunari@mini:~$

LS-SL 楽天市場