シャシからできるだけはみ出さないようにした。
これで、LS-WSGL のようにケースを切らなくてもケースに納められるかな。
Orion1 CPU = Low
Checking DATA BUS
Checking ADDRESS BUS
> Checking hardware info ...
=== CPU-ID : 0x00005182 ===
=== Strap status : 0x00802030 ===
=== H/W boardId : 0x33 ===
=== boardId : 0x1a ===
=== micon_support: off ===
> OK.
=== BUFFALO LS-SL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_SL LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (May 28 2009 - 11:06:21) Marvell version: 1.12.1 - TINY
U-Boot code: 00600000 -> 00639A58 BSS: -> 00641B24
Buffalo Version: 1.23-1.00
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz
USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1118 phy
buffalo_change_power_status > Read 0x3a
buffalo_IsStopAtUbootStatus > MagicKey=0x3a
buffalo_change_power_status > Read 0x3a
buffalo_change_power_status > Read 0x3a
buffalo_change_power_status > Writing 0x5c
Please Press HDD power button to continue ...
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a
Marvell Serial ATA Adapter
Integrated Sata device found
Device 0: OK
Model: WDC WD5000BEVT-00ZAT0 Firm: 01.01A01 Ser#: WD-WX50A79U4140
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
2120012 bytes read
Image Name: Linux-2.6.22.7
Created: 2009-06-14 13:44:50 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2119948 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
8937716 bytes read
Image Name: initrd
Created: 2009-06-14 13:46:10 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 8937652 Bytes = 8.5 MB
Load Address: 00000000
Entry Point: 00000000
** Bad partition 1 **
serch_boot_drv (194)>No kernel_file 1
** Bad partition 1 **
serch_boot_drv (249)>No init_file 1
Booting from Device 0
hit any key to switch tftp boot.
Hit any key to stop autoboot: 0
Hit any key to stop autoboot: 0
2120012 bytes read
** Bad partition 1 **
## Booting image at 00100000 ...
Image Name: Linux-2.6.22.7
Created: 2009-06-14 13:44:50 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 2119948 Bytes = 2 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
Image Name: initrd
Created: 2009-06-14 13:46:10 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 8937652 Bytes = 8.5 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.23
CONFIG_BUFFALO_PLATFORM ---
Uncompressing Linux..................................................................................................................................... done, booting the kernel.
Linux version 2.6.22.7 (root@build2.dd-hot24.nas.buffalo.local) (gcc version 4.2.0 20070413 (prerelease)) #436 Sun Jun 14 22:44:37 JST 2009
CPU: ARM926EJ-S [41069260] revision 0 (ARMv5TEJ), cr=a0053177
Machine: Feroceon
Using UBoot passing parameters structure
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists. Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.23
PID hash table entries: 512 (order: 9, 2048 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110136KB available (3832K code, 294K data, 120K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
env_format_version = 0x00000006
product_id = 0x00000013
Sys Clk = 200000000, Tclk = 166664740
CPU Interface
-------------
SDRAM_CS0 ....base 00000000, size 128MB
SDRAM_CS1 ....disable
SDRAM_CS2 ....disable
SDRAM_CS3 ....disable
PEX0_MEM ....base e0000000, size 128MB
PEX0_IO ....base f2000000, size 1MB
PCI0_MEM ....base e8000000, size 128MB
PCI0_IO ....base f2100000, size 1MB
INTER_REGS ....base f1000000, size 1MB
DEVICE_CS0 ....no such
DEVICE_CS1 ....base f4000000, size 32MB
DEVICE_CS2 ....no such
DEV_BOOCS ....base ff800000, size 8MB
CRYPT_ENG ....base f0000000, size 64KB
Marvell Development Board (LSP Version 3.0.5_NAS_GDP_p8)-- BUFFALO_BOARD Soc: 88F5182 A2
Detected Tclk 166664740 and SysClk 200000000
Marvell USB EHCI Host controller #0: c055b600
Marvell USB EHCI Host controller #1: c055b400
IO Request resource failed - Pci If 0
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
Time: orion_clocksource clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
RTC has been updated!!!RTC registered
mvCesaInit: sessions=640, queue=64, pSram=f0000000
Use the XOR engines (acceleration) for enhancing the following functions:
o RAID 5 Xor calculation
o kernel memcpy
o kenrel memzero
o copy user to/from kernel buffers
Number of XOR engines to use: 2
Use IDMA channels 2 and 3 for enhancing the following function:
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SGI XFS with ACLs, large block numbers, no debug enabled
SGI XFS Quota Management subsystem
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
serial8250.0: ttyS2 at MMIO 0xf1012100 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 32768K size 1024 blocksize
loop: module loaded
Marvell Ethernet Driver 'mv_ethernet':
o Uncached descriptors in DRAM
o DRAM SW cache-coherency
o TCP segmentation offload enabled
o Checksum offload enabled
o Rx desc: 128
o Tx desc: 256
o Loading network interface ** eth_init_module (0)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
scsi 0:0:0:0: Direct-Access WDC WD5000BEVT-00ZAT 01.0 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
sda: sda1 sda2 sda3 sda4 sda5 sda6
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
physmap platform flash device: 01000000 at f0000000
physmap-flash physmap-flash.0: map_probe failed
Found: SST 39LF020
cfi_flash_0: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
mice: PS/2 mouse device common for all mice
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
raid6: int32x1 20 MB/s
raid6: int32x2 28 MB/s
raid6: int32x4 35 MB/s
raid6: int32x8 31 MB/s
raid6: using algorithm int32x4 (35 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
raid5: measuring checksumming speed
arm4regs : 308.800 MB/sec
8regs : 252.800 MB/sec
32regs : 274.400 MB/sec
raid5: using function: arm4regs (308.800 MB/sec)
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.0.02 installed.
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
---- in linuxrc ---
Version 1.00 2008/ 7/ 1
grep: /var/tmp/devlink: No such file or directory
Thu Nov 1 00:00:00 JST 2007
Thu Nov 1 00:00:00 JST 2007
CheckDevices
grep: /var/tmp/devlink: No such file or directory
linuxrc:choose operation (timeout 4[s])
1:RamRoot other:HddRoot ? -HddRoot-
-- rebuild mdadm.conf for BOOT, ROOTFS --
md: md10 stopped.
mdadm: /dev/diskmd: md1 stopped.
1_1 has wrong uuid.
mdadm: no devices found for /dev/md10
md: md0 stopped.
mdadm: /dev/disk1_1 has wrong uuid.
mdadm: no devices found for /dev/md1
md: bind<sda1>
raid1: raid set md0 active with 1 out of 2 mirrors
mdadm: /dev/md0 has been started with 1 drive (out of 2).
-- setup max error counts --
/sys/block/md0/md/maxerr_cnt is setted to -1
Starting :fsck_disks(boot) ... [Failed. ]
Starting :fsck_disks(rootfs) ... [Success.]
Starting :mount(boot) ... kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
[Success.]
Starting :umount(boot) ... [Success.]
-- rebuild mdadm.conf for BOOT, ROOTFS --
md: md10 stopped.
mdadm: cannot open device /dev/disk1_1: Device or resource busy
mdadm: /dev/disk1_1 has wrong uuid.
mdadm: /demd: bind<sda5>
v/disk1_2 has wrong uuid.
raid1: raid set md10 active with 1 out of 2 mirrors
mdadm: /dev/md10md: md1 stopped.
has been started with 1 drive (out of 2).
md: bind<sda2>
raid1: raid set md1 active with 1 out of 2 mirrors
mdadm: /dev/md1 has been started with 1 drive (out of 2).
-- setup max error counts --
/sys/block/md0/md/maxerr_cnt is setted to -1
/sys/block/md1/md/maxerr_cnt is setted to -1
/sys/block/md10/md/maxerr_cnt is setted to -1
Filesystem "md1": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md1
PRODUCTID=0x00000013 PRODUCTID=0x00000000
-- CopyFromInitrdToHdd --
.........Finish
umount: cannot open /proc/mounts
Filesystem "md1": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md1
VFS: Mounted root (xfs filesystem).
Trying to move old root to /initrd ... okay
Freeing init memory: 120K
init started: BusyBox v1.7.0 (2007-10-15 19:49:46 IST)
starting pid 503, tty '': '/etc/init.d/rcS'
--- rcStart (hddroot) ---
Thu Nov 1 00:00:10 JST 2007
** step1 **
=== checkroot.sh ===
grep: /var/tmp/devlink: No such file or directory
Filesystem "md1": Disabling barriers, not supported by the underlying device
mount: mounting /dev/root on / failed: No such file or directory
ln: /var/spool/cron/cron: File exists
grep: /var/tmp/devlink: No such file or directory
Adding 999864k swap on /dev/md10. Priority:-1 extents:1 across:999864k
=== procps.sh ===
=== devpts.sh ===
=== sethostname.sh ===
configure files from Buffalo parameters.
=== restore_config.sh ===
kjournald starting. Commit interval 5 seconds
EXT3 FS on md0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Update configuration files
Restore previous configuration files
delete unnecessary samba lock files on /tmp/upconfig//etc/samba/lock...
=== free_ramdisk.sh ===
Successfully unmounted /dev/ram0
Successfully unmounted /dev/ram0
=== vm_tune.sh ===
** step2 **
=== EnablingAutoip.sh ===
=== usb.sh ===
/sbin/hotplug [module]
/sbin/hotplug [drivers]
usbcore: registered new interface driver usbfs
/sbin/hotplug [drivers]
usbcore: registered new interface driver hub
/sbin/hotplug [drivers]
usbcore: registered new device driver usb
/sbin/hotplug [module]
/sbin/hotplug [drivers]
ehci_marvell ehci_marvell.4523: Marvell Orion EHCI
/sbin/hotplug [usb_host]
ehci_marvell ehci_marvell.4523: new USB bus registered, assigned bus number 1
ehci_marvell ehci_marvell.4523: irq 17, io base 0xf1050100
ehci_marvell ehci_marvell.4523: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
/sbin/hotplug [usb]
/sbin/hotplug [usb_endpoint]
usb usb1: configuration #1 chosen from 1 choice
/sbin/hotplug [usb]
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
/sbin/hotplug [usb_endpoint]
/sbin/hotplug [usb_device]
[/etc/hotplug.d/usb_device/buffalo.hotplug] usb_device
ehci_marvell ehci_marvell.167817: Marvell Orion EHCI
/sbin/hotplug [usb_host]
ehci_marvell ehci_marvell.167817: new USB bus registered, assigned bus number 2
ehci_marvell ehci_marvell.167817: irq 12, io base 0xf10a0100
ehci_marvell ehci_marvell.167817: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
/sbin/hotplug [usb]
/sbin/hotplug [usb_endpoint]
usb usb2: configuration #1 chosen from 1 choice
/sbin/hotplug [usb]
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
/sbin/hotplug [usb_endpoint]
/sbin/hotplug [usb_device]
[/etc/hotplug.d/usb_device/buffalo.hotplug] usb_device
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
USB Universal Host Controller Interface driver v3.0
/sbin/hotplug [drivers]
/sbin/hotplug [module]
Initializing USB Mass Storage driver...
/sbin/hotplug [drivers]
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
/sbin/hotplug [module]
/sbin/hotplug [drivers]
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
=== hotplug.sh ===
*** /usr/local/bin/DirectCopy_wait.sh [stop]
cat: can't open '/var/run/DirectCopy_wait.pid': No such file or directory
=== networking.sh ===
/etc/init.d/networking.sh : Clear /etc/dhcpc/dhcpcd-eth0.pid eth0
/etc/init.d/networking.sh : Read dhcpc file eth0
/etc/init.d/networking.sh : configure : eth0
create network files.. (eth0)
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
/etc/init.d/networking.sh : Delete /etc/dhcpc/dhcpcd-eth0.pid
route: SIOCDELRT: No such process
Configuration network interface: eth0
/sbin/ifconfig eth0 mtu 1500 multicast
/etc/init.d/networking.sh: line 373: /proc/sys/net/ipv4/conf/eth1/arp_ignore: No such file or directory
requesting DHCP tout=30[s]
networking.sh: dhcp requesting...
DontDownIfaceeth reg(9) val=0x0300
eth0: link down
alwaysFork
eth0: link up, full duplex, speed 1 Gbps
sendto: count 6 sync 1
sendto: count 5 sync 0
dhcpcd.exe: interface eth0 has been configured with old IP=192.168.2.207 GATEWAY=192.168.2.1
** eth0 : networking.sh dhcp fin.
configure files from Buffalo parameters.
=== update_ntp.sh ===
/etc/init.d/update_ntp.sh: line 17: /usr/local/bin/time_set.sh: No such file or directory
=== syslog.sh ===
Starting system logger:
Starting kernel logger:
=== network_control.sh ===
=== inetd.sh ===
Starting inetd:=== errormon.sh ===
Starting errormon:errormon ver.1.01(BuildDate Jun 12 2009 13:30:29 compiled for BUFFALO NAS Series) Started
=== kernelmon.sh ===
Starting kernelmon:=== miconmon.sh ===
=== checkSysMd.sh ===
KERNELMOn (lanact 0 half)
/dev/md0
Raid Level : raid1
KERNELMOn (lanact 1000 full)
/dev/md1
Raid Level : raid1
/dev/md10
Raid Level : raid1
/etc/init.d/networking.sh : Clear /etc/dhcpc/dhcpcd-eth0.pid eth0
/etc/init.d/networking.sh : Read dhcpc file eth0
=== start_data_array.sh ===
-- start data arrays --
-- rebuild mdadm.conf for md2,md3--
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
mdadm: No arrays found in config file
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
/sbin/hotplug [block]
-- setup max error counts --
/sys/block/md2/md/maxerr_cnt is setted to -1
/sys/block/md3/md/maxerr_cnt is setted to -1
/sys/block/md4/md/maxerr_cnt is setted to -1
-- check /etc/melco/diskinfo and real RAID disks. --
RAID is not normal. rebuild /etc/melco/diskinfo file.
mdadm: No arrays found in config file
-- Mount local disks --
XFS mounting filesystem sda6
=== set_quota.sh ===
** step3 **
=== diskmon.sh ===
=== drivecheck.sh ===
=== ftpd.sh ===
ftp is OFF
=== atalk.sh ===
atalk is OFF
=== httpd.sh ===
start
Starting HTTPD services: cat: can't open '/etc/apache/server.key': No such file or directory
cat: can't open '/etc/apache/server.crt': No such file or directory
2009-10-30 21:27:54: (configfile.c.901) opening configfile /etc/buffalo-web_https.conf failed: No such file or directory
=== smb.sh ===
configure samba
LoadConfFileString:key=[local_auth] not found in /etc/melco/info.
load_info ItemValue = off
LoadConfFileString:key=[ad_dns] not found in /etc/melco/info.
LoadConfFileOnOff:key=[info_visible] not found in /etc/melco/info.
LoadConfFileString:key=[array2] not found in /etc/melco/diskinfo.
LoadConfFileString:key=[usb_disk2] not found in /etc/melco/diskinfo.
LoadConfFileString:key=[msdfs_link1_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link2_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link3_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link4_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link5_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link6_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link7_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link8_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link9_name] not found in /etc/melco/msdfs.
file:/etc/samba/smb.conf
>IconvCodeCharset CodePage=0,charset=CP932
buf=array1=off
buf=disk1=normal
GetSpoolDirectory> returning devicename [/mnt/disk1]
file:/etc/pam_smb.conf
Setting up msdfs symbolic links... [Failed ]
Starting SMB services:
Starting NMB services:
=== clientUtil_servd.sh ===
Starting clientUtil_server:starting on eth0
=== bonjour.sh ===
Starting Bonjour services: done
=== lsprcvd.sh ===
Starting lsprcvd:=== daemonwatch.sh ===
Starting daemonwatch:daemonwatch Ver.1.01
watch list file : /etc/daemonwatch.list
=== cron.sh ===
Start services: crondlogrotate state -- version 2
=== checkconfig.sh ===
=== ups.sh ===
err:
err:
=== pwrmgr.sh ===
Starting pwrmgr:
Shutting down pwrmgr:
Starting pwrmgr:
** step4 **
=== modules.sh ===
Starting module subsystem ...
Starting module webaxs ... [Success.]
=== itunes.sh ===
=== lprng.sh ===
/mnt/disk1/spool/samba created
/mnt/disk1/spool/lp created
Start services: lpd
/etc/init.d/lprng.sh: line 129: /usr/local/sbin/lprmd: No such file or directory
=== ltbootd.sh ===
Starting services: rarpd tftpd rarpcfgd fwupdated.
=== pmcd.sh ===
=== webaxs.sh ===
WebAccess is OFF
=== twonky.sh ===
TwonkyMedia Version 4.4.8
LOG_SYSTEM: reading ini file: "/usr/local/twonky/twonkyvision-mediaserver.ini".
/mnt/disk1/share%HOSTNAME%: LinkStationjpbittorrent is off
=== bootcomplete.sh ===
** step final(after bootcomplete) **
=== hdd_late_check.sh ===
No need to check hdd(hdd is fine).
No new disks.
=== check_initialization.sh ===
bootarg "func" is disabled.
=== usb_late_check.sh ===
starting pid 2410, tty '': '/sbin/getty'
nothing to delete
*** /usr/local/bin/DirectCopy_wait.sh [start]
BUFFALO INC. LinkStation series
LS-SL807 login: 1 USB_DEVICE=none
2 USB_DEVICE=none
3 USB_DEVICE=none
4 USB_DEVICE=none
5 USB_DEVICE=none
KERNELMOn (PSW_on)
Shutting down pwrmgr:
BUFFALO INC. LinkStation series
LS-SL807 login: admin
Password:
No mail.
-sh: /etc/profile: Permission denied
-sh-3.2$
ちゃんと半田付けしたので、文字化けもしていない。
|
|
← シリアルコンソール |
ハックの記録 LinkStation／玄箱 をハックしよう |
→ K-OF 展示環境 |
