ファームウェア 1.10 βでハックキット（４）

LED の確認

USB メモリの認識

qube:~# tail -f /var/log/messages
Jun 16 22:22:40 qube kernel: usb usb2: configuration #1 chosen from 1 choice
Jun 16 22:22:40 qube kernel: hub 2-0:1.0: USB hub found
Jun 16 22:22:40 qube kernel: hub 2-0:1.0: 1 port detected
Jun 16 22:22:40 qube kernel: USB Universal Host Controller Interface driver v3.0
Jun 16 22:22:40 qube kernel: Initializing USB Mass Storage driver...
Jun 16 22:22:40 qube kernel: usbcore: registered new interface driver usb-storage
Jun 16 22:22:40 qube kernel: USB Mass Storage support registered.
Jun 16 22:22:40 qube kernel: usbcore: registered new interface driver usblp
Jun 16 22:22:40 qube kernel: drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Jun 16 22:22:41 qube kernel: eth0: link up, full duplex, speed 1 Gbps
usb 1-1: new full speed USB device using ehci_marvell and address 2
usb 1-1: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
Jun 16 22:24:33 qube kernel: usb 1-1: new full speed USB device using ehci_marvell and address 2
Jun 16 22:24:34 qube kernel: usb 1-1: configuration #1 chosen from 1 choice
Jun 16 22:24:34 qube kernel: scsi2 : SCSI emulation for USB Mass Storage devices
scsi 2:0:0:0: Direct-Access     eUSB     Memory Stick     5.06 PQ: 0 ANSI: 2
Jun 16 22:24:40 qube kernel: scsi 2:0:0:0: Direct-Access     eUSB     Memory Stick     5.06 PQ: 0 ANSI: 2
sd 2:0:0:0: [sdb] 126912 512-byte hardware sectors (65 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Assuming drive cache: write through
sd 2:0:0:0: [sdb] 126912 512-byte hardware sectors (65 MB)
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 2:0:0:0: [sdb] Attached SCSI removable disk
sd 2:0:0:0: Attached scsi generic sg1 type 0
Jun 16 22:24:40 qube kernel: sd 2:0:0:0: [sdb] 126912 512-byte hardware sectors (65 MB)
Jun 16 22:24:40 qube kernel: sd 2:0:0:0: [sdb] Write Protect is off
Jun 16 22:24:40 qube kernel: sd 2:0:0:0: [sdb] 126912 512-byte hardware sectors (65 MB)
Jun 16 22:24:40 qube kernel: sd 2:0:0:0: [sdb] Write Protect is off
Jun 16 22:24:40 qube kernel: sdb: sdb1
Jun 16 22:24:40 qube kernel: sd 2:0:0:0: [sdb] Attached SCSI removable disk
Jun 16 22:24:40 qube kernel: sd 2:0:0:0: Attached scsi generic sg1 type 0

usb 1-1: USB disconnect, address 2
Jun 16 22:25:30 qube kernel: usb 1-1: USB disconnect, address 2

usb 2-1: new full speed USB device using ehci_marvell and address 2
usb 2-1: configuration #1 chosen from 1 choice
scsi3 : SCSI emulation for USB Mass Storage devices
scsi 3:0:0:0: Direct-Access     eUSB     Memory Stick     5.06 PQ: 0 ANSI: 2
sd 3:0:0:0: [sdb] 126912 512-byte hardware sectors (65 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Assuming drive cache: write through
sd 3:0:0:0: [sdb] 126912 512-byte hardware sectors (65 MB)
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Assuming drive cache: write through
 sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI removable disk
sd 3:0:0:0: Attached scsi generic sg1 type 0

プリンタの認識

usb 1-1: new full speed USB device using ehci_marvell and address 3
usb 1-1: configuration #1 chosen from 1 choice
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005
Jun 16 22:26:05 qube kernel: usb 2-1: new full speed USB device using ehci_marvell and address 2
Jun 16 22:26:05 qube kernel: usb 2-1: configuration #1 chosen from 1 choice
Jun 16 22:26:05 qube kernel: scsi3 : SCSI emulation for USB Mass Storage devices
Jun 16 22:26:11 qube kernel: scsi 3:0:0:0: Direct-Access     eUSB     Memory Stick     5.06 PQ: 0 ANSI: 2
Jun 16 22:26:11 qube kernel: sd 3:0:0:0: [sdb] 126912 512-byte hardware sectors (65 MB)
Jun 16 22:26:11 qube kernel: sd 3:0:0:0: [sdb] Write Protect is off
Jun 16 22:26:12 qube kernel: sd 3:0:0:0: [sdb] 126912 512-byte hardware sectors (65 MB)
Jun 16 22:26:12 qube kernel: sd 3:0:0:0: [sdb] Write Protect is off
Jun 16 22:26:12 qube kernel: sdb: sdb1
Jun 16 22:26:12 qube kernel: sd 3:0:0:0: [sdb] Attached SCSI removable disk
Jun 16 22:26:12 qube kernel: sd 3:0:0:0: Attached scsi generic sg1 type 0
Jun 16 22:27:08 qube kernel: usb 2-1: USB disconnect, address 2
Jun 16 22:28:37 qube kernel: usb 1-1: new full speed USB device using ehci_marvell and address 3
Jun 16 22:28:38 qube kernel: usb 1-1: configuration #1 chosen from 1 choice
Jun 16 22:28:38 qube kernel: drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04B8 pid 0x0005

リブートの確認

qube:~# shutdown -r now
INIT: Sending pStopping Samba daemons: nmbd smbd.
Stopping internet superserver: inetd.
Stopping NTP server: ntpd.
Saving the system clock.
Stopping enhanced syslogd: rsyslogd.
Asking all remaining processes to terminate...done.
Killing all remaining processes...failed.
Deconfiguring network interfaces...done.
Cleaning up ifupdown....
Deactivating swap...done.
Unmounting local filesystems...done.
Will now restart.
md: stopping all md devices.
md: md1 still in use.
md: md10 switched to read-only mode.
md: md0 switched to read-only mode.
sd 0:0:0:0: [sda] Synchronizing SCSI cache
Restarting system.
Reseting !!
Orion1   CPU =  Low

Checking DATA BUS
Checking ADDRESS BUS

> Checking hardware info ...
=== CPU-ID       : 0x00005182 ===
=== Strap status : 0x00801030 ===
=== H/W boardId  :       0x2b ===
=== boardId      :       0x1f ===
=== micon_support:        off ===
> OK.
=== BUFFALO LS-QL/R5 U-Boot. ===
 ** LOADER **
 ** BUFFALO BOARD: BUFFALO_BOARD_LS_QL_R5 LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (May 20 2009 - 10:06:17) Marvell version: 1.12.1 - TINY
Buffalo Version: 1.27-1.00

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 200Mhz , TClock = 166Mhz


USB 0: host mode
Net:   egiga0 [PRIME]
Using 88E1118 phy

Marvell Serial ATA Adapter
Integrated Sata device found
found port multi device 0
PM found

buffalo_change_power_status > Read 0x18
buffalo_IsStopAtUbootStatus > MagicKey=0x18
buffalo_change_power_status > Read 0x18
buffalo_change_power_status > Read 0x18
buffalo_change_power_status > Writing 0x3a
HDD1 Power ON
HDD2 Power ON
HDD3 Power ON
HDD4 Power ON

Marvell Serial ATA Adapter
Integrated Sata device found
Port Multiplier found @ 0 0. Vendor: 11ab ports: 4

HDD is not found

シャットダウンの確認

LS-QL バッファローダイレクト 楽天市場 amazon livedoorデパート Sofmap バリューモア Yahoo!ショッピングトップ パソQ ムラウチドットコム