Orion1 CPU = Low > Checking hardware info ... === Strap status : 0x00800030 === === H/W boardId : 0x23 === === boardId : 0x1b === === micon_support: off === > OK. === BUFFALO LS-HGL U-Boot. === ** LOADER ** ** BUFFALO BOARD: BUFFALO_BOARD_LS_HGL LE (CFG_ENV_ADDR=fffff000) U-Boot 1.1.1 (Feb 4 2008 - 20:03:55) Marvell version: 1.12.1 - TINY Buffalo Version: 1.13-1.00 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB [256kB@fffc0000] Flash: 256 kB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M): Done Soc: 88F5182 A2 CPU: ARM926 (Rev 0) running @ 400Mhz Orion 1 streaming disabled SysClock = 250Mhz , TClock = 166Mhz USB 0: host mode PCI 0: PCI Express Root Complex Interface PCI 1: Conventional PCI, speed = 33000000 Net: egiga0 [PRIME] Using 88E1118 phy buffalo_change_power_status > Read 0x5c buffalo_IsStopAtUbootStatus > MagicKey=0x5c buffalo_change_power_status > Read 0x5c buffalo_change_power_status > Read 0x5c buffalo_change_power_status > Writing 0x5c Please Press HDD power button to continue ...ここで止まる。
buffalo_change_power_status > Read 0x5c
buffalo_change_power_status > Writing 0x3a
Marvell Serial ATA Adapter
Integrated Sata device found
Device 0: OK
Model: SAMSUNG HD250HJ Firm: FH100-05 Ser#: S17TJDWQ100470
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/initrd.buffalo
5965438 bytes read
Using device ide1, partition 1
** Bad partition 1 **
Booting from Device 0
hit any key to switch tftp boot.
Hit any key to stop autoboot: 0
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Device 0: OK
Model: SAMSUNG HD250HJ Firm: FH100-05 Ser#: S17TJDWQ100470
Type: Hard Disk
Supports 48-bit addressing
Capacity: 238475.1 MB = 232.8 GB (488397168 x 512)
Using device ide0, partition 1
Loading from block device ide device 0, partition 1: Name: hda1
Type: U-Boot File:/uImage.buffalo
1715664 bytes read
Using device ide1, partition 1
** Bad partition 1 **
## Booting image at 00100000 ...
Image Name: Linux-2.6.16.16-arm1
Created: 2008-02-21 2:41:51 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1715600 Bytes = 1.6 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
## Loading Ramdisk Image at 00800000 ...
Image Name: initrd
Created: 2008-02-21 2:44:17 UTC
Image Type: ARM Linux RAMDisk Image (gzip compressed)
Data Size: 5965374 Bytes = 5.7 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Starting kernel ...
arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.13
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSHGL ---
Uncompressing Linux................................................................................................................ done, booting the kernel.
Linux version 2.6.16.16-arm1 (root@build.dd-hot24.nas.buffalo.local) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #304 Thu Feb 21 11:41:19 JST 2008
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740
- Warning - This LSP release was tested only with U-Boot release 1.7.3
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 func=0 BOOTVER=1.13
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 110720KB available (2912K code, 550K data, 108K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 15360K
NET: Registered protocol family 16
FLASH boardId = 1a
Flash bankwidth 1, base ff800000, size 40000
BUFFALO LS_HGL FLASH size 256[KB]
Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_HGL
Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c16f5e00
Marvell USB EHCI Host controller #1: c16f5c00
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
cesadev_init(c0011434)
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
SGI XFS with large block numbers, no debug enabled
Initializing Cryptographic API
io scheduler noop registered (default)
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
o Ethernet descriptors in DRAM
o DRAM SW cache-coherency
o Checksum offload enabled
o Loading network interface ** egiga_init_module (0)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
** BUFFALO Disable Command Queuing Function [0 0] **
Vendor: SAMSUNG Model: HD250HJ Rev: FH10
Type: Direct-Access ANSI SCSI revision: 03
Linux IAL (ERROR) : retry command host=0, bus=0 SCpnt = c141fba0
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda4 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
physmap flash device: 40000 at ff800000
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
mice: PS/2 mouse device common for all mice
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Buffalo CPU Inerupts Driver (C) BUFFALO INC. Ver.0.01 alpha1 installed.
mvGppValueSet: Err. An attempt to set output value to GPP 2 in input mode.
Buffalo Gpio Control Driver (C) BUFFALO INC. Ver.0.01 installed.
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
---- in linuxrc ---
Thu Nov 1 03:05:19 JST 2007
CheckDevices
linuxrc:choose operation (timeout 4[s])
1:RamRoot other:HddRoot ? -HddRoot-
Starting :fsck_disks(boot) ... [Success.]
Starting :fsck_disks(rootfs) ... XFS mounting filesystem sda2
/sbin/hotplug [block]
/sbin/hotplug [block]
[Success.]
Starting :mount(boot) ... kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
/sbin/hotplug [block]
[Success.]
Starting :umount(boot) ... /sbin/hotplug [block]
[Success.]
XFS mounting filesystem sda2
/sbin/hotplug [block]
PRODUCTID=0x0000000E PRODUCTID=0x0000000E
KERNEL:2008/2/21 11:41:11
HDD:2008/2/21 11:53:16
KERNEL:2008/2/21 11:42:55
HDD:2008/2/21 11:53:16
-- CopyFromInitrdToHdd --
.........Finish
/sbin/hotplug [block]
XFS mounting filesystem sda2
VFS: Mounted root (xfs filesystem).
Trying to move old root to /initrd ... okay
Freeing init memory: 108K
init started: BusyBox v1.1.1 (2008.01.18-06:21+0000) multi-call binary
Starting pid 537, console /dev/ttyS0: '/etc/init.d/rcS'
--- rcStart (hddroot) ---
Thu Nov 1 03:05:36 JST 2007
umount: /etc/pwrmgr: not mounted
** step1 **
mount: mount point /proc/bus/usb/ does not exist
mount: /dev/pts already mounted or /dev/pts busy
mount: according to mtab, devpts is already mounted on /dev/pts
mkdir: Cannot create directory `/var/lock': File exists
ln: /var/spool/cron/cron: File exists
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
Adding 1004020k swap on /dev/sda5. Priority:-1 extents:1 across:1004020k
configure files from Buffalo parameters.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
/sbin/hotplug [block]
Update configuration files
Restore previous configuration files
/bin/tar: etc/atalk/AppleVolumes.system: time stamp 2008-01-09 10:30:40 is 5988298.919891 s in the future
/bin/tar: etc/atalk/papd.conf: time stamp 2008-01-09 10:30:40 is 5988298.910519 s in the future
/bin/tar: etc/atalk: time stamp 2008-02-21 12:00:33 is 9708891.909547 s in the future
/bin/tar: etc/cron/crontabs/root: time stamp 2008-01-09 10:30:42 is 5988300.909077 s in the future
/bin/tar: etc/melco/crontabs: time stamp 2008-02-21 12:00:33 is 9708891.908542 s in the future
/bin/tar: etc/melco/pdcuserinfo: time stamp 2008-01-09 10:30:41 is 5988299.908154 s in the future
/bin/tar: etc/melco/timer_status: time stamp 2008-01-09 10:30:41 is 5988299.907625 s in the future
/bin/tar: etc/melco/raidscan: time stamp 2008-01-09 10:30:41 is 5988299.907072 s in the future
/bin/tar: etc/melco/email: time stamp 2008-01-09 10:30:41 is 5988299.906455 s in the future
/bin/tar: etc/melco/lcdled: time stamp 2008-01-09 10:30:41 is 5988299.905923 s in the future
/bin/tar: etc/melco/usbshareinfo: time stamp 2008-01-09 10:30:41 is 5988299.905371 s in the future
/bin/tar: etc/melco/userinfo: time stamp 2008-01-09 10:30:41 is 5988299.904841 s in the future
/bin/tar: etc/melco/autoadduserinfo: time stamp 2008-01-09 10:30:41 is 5988299.904395 s in the future
/bin/tar: etc/melco/pdcgroupinfo: time stamp 2008-01-09 10:30:41 is 5988299.903932 s in the future
/bin/tar: etc/melco/caution: time stamp 2008-01-09 10:30:41 is 5988299.903406 s in the future
/bin/tar: etc/melco/lcd_status: time stamp 2008-01-09 10:30:41 is 5988299.902856 s in the future
/bin/tar: etc/melco/diskinfo: time stamp 2008-02-27 13:47:52 is 10233730.902323 s in the future
/bin/tar: etc/melco/ups: time stamp 2008-01-09 10:30:41 is 5988299.901793 s in the future
/bin/tar: etc/melco/groupinfo: time stamp 2008-01-09 10:30:41 is 5988299.901248 s in the future
/bin/tar: etc/melco/ls_list: time stamp 2008-01-09 10:30:41 is 5988299.895857 s in the future
/bin/tar: etc/melco/backup_dstlist: time stamp 2008-01-09 10:30:41 is 5988299.895388 s in the future
/bin/tar: etc/melco/msdfs: time stamp 2008-01-09 10:30:41 is 5988299.89485 s in the future
/bin/tar: etc/melco/seach_list: time stamp 2008-01-09 10:30:41 is 5988299.894388 s in the future
/bin/tar: etc/melco/DirectCopy: time stamp 2008-02-12 22:25:42 is 8968800.893856 s in the future
/bin/tar: etc/melco/dlnaserver: time stamp 2008-02-18 23:29:19 is 9491017.892988 s in the future
/bin/tar: etc/melco/ituneserver: time stamp 2008-02-20 15:49:57 is 9636255.892454 s in the future
/bin/tar: etc/melco/shareinfo: time stamp 2008-02-27 13:47:52 is 10233730.891106 s in the future
/bin/tar: etc/melco/shareinfo.hidden: time stamp 2008-02-27 13:47:52 is 10233730.89057 s in the future
/bin/tar: etc/melco/shareinfo.vfs: time stamp 2008-02-27 13:47:52 is 10233730.890093 s in the future
/bin/tar: etc/melco/offlinefile: time stamp 2008-02-27 13:47:52 is 10233730.889559 s in the future
/bin/tar: etc/melco/info: time stamp 2008-02-27 13:48:04 is 10233742.889005 s in the future
/bin/tar: etc/pam.d/sudo: time stamp 2008-02-21 12:00:33 is 9708891.885389 s in the future
/bin/tar: etc/pam.d: time stamp 2008-02-21 12:00:33 is 9708891.870906 s in the future
/bin/tar: etc/proftpd: time stamp 2008-02-21 12:00:33 is 9708891.870065 s in the future
/bin/tar: etc/samba/lock/gencache.tdb: time stamp 2008-02-27 13:47:18 is 10233696.869442 s in the future
/bin/tar: etc/samba/lock/registry.tdb: time stamp 2008-02-27 13:47:19 is 10233697.862954 s in the future
/bin/tar: etc/samba/lock/group_mapping.tdb: time stamp 2008-02-27 13:47:18 is 10233696.862228 s in the future
/bin/tar: etc/samba/lock/account_policy.tdb: time stamp 2008-02-27 13:47:18 is 10233696.861594 s in the future
/bin/tar: etc/samba/lock/perfmon: time stamp 2008-02-27 13:47:19 is 10233697.861143 s in the future
/bin/tar: etc/samba/lock/printing/lp.tdb: time stamp 2008-02-27 13:47:19 is 10233697.854416 s in the future
/bin/tar: etc/samba/lock/printing: time stamp 2008-02-27 13:47:19 is 10233697.854052 s in the future
/bin/tar: etc/samba/lock/ntdrivers.tdb: time stamp 2008-02-27 13:47:19 is 10233697.853485 s in the future
/bin/tar: etc/samba/lock/ntprinters.tdb: time stamp 2008-02-27 13:47:19 is 10233697.852939 s in the future
/bin/tar: etc/samba/lock/ntforms.tdb: time stamp 2008-02-27 13:47:19 is 10233697.84645 s in the future
/bin/tar: etc/samba: time stamp 2008-02-21 12:00:33 is 9708891.8447 s in the future
/bin/tar: etc/ftpusers: time stamp 2008-01-09 10:30:43 is 5988301.84425 s in the future
/bin/tar: etc/gshadow: time stamp 2008-01-09 10:30:43 is 5988301.84341 s in the future
/bin/tar: etc/passwd: time stamp 2008-01-09 10:30:43 is 5988301.842406 s in the future
/bin/tar: etc/shadow: time stamp 2008-03-02 17:38:44 is 10593182.841871 s in the future
/bin/tar: etc/shadow.orig: time stamp 2008-01-09 10:30:43 is 5988301.841423 s in the future
/bin/tar: modules/webaxs/etc: time stamp 2008-02-27 13:47:52 is 10233730.838175 s in the future
delete unnecessary samba lock files on /tmp/upconfig//etc/samba/lock...
tar: var/log/apache/access_log: time stamp 2008-02-27 13:47:28 is 10233706.773983 s in the future
tar: var/log/apache: time stamp 2008-02-27 13:47:28 is 10233706.772713 s in the future
tar: var/log/cores/smbd: time stamp 2008-02-27 13:47:17 is 10233695.762371 s in the future
tar: var/log/cores/nmbd: time stamp 2008-02-27 13:47:18 is 10233696.761724 s in the future
tar: var/log/cores: time stamp 2008-02-27 13:47:18 is 10233696.76134 s in the future
tar: var/log/file.smb: time stamp 2008-02-27 13:47:23 is 10233701.723381 s in the future
tar: var/log: time stamp 2008-02-27 13:47:47 is 10233725.71998 s in the future
** step2 **
#[miconapl.usb_set_power]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
usbcore: registered new driver usbfs
/sbin/hotplug [drivers]
usbcore: registered new driver hub
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
ehci_platform ehci_platform.4523: EHCI Platform Host Controller
/sbin/hotplug [usb_host]
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
/sbin/hotplug [usb]
usb usb1: configuration #1 chosen from 1 choice
/sbin/hotplug [usb]
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
/sbin/hotplug [usb_device]
ehci_platform ehci_platform.16781: EHCI Platform Host Controller
/sbin/hotplug [usb_host]
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004
/sbin/hotplug [usb]
usb usb2: configuration #1 chosen from 1 choice
/sbin/hotplug [usb]
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
/sbin/hotplug [usb_device]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
Initializing USB Mass Storage driver...
/sbin/hotplug [drivers]
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
/sbin/hotplug [module]
/sbin/hotplug [drivers]
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
ls: /proc/scsi/usb-storage/: No such file or directory
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP tout=30[s]
networking.sh: dhcp requesting...
DontDownIfaceeth0: link down
alwaysFork
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
sendto: count 6 sync 1
sendto: count 5 sync 0
dhcpcd.exe: interface eth0 has been configured with old IP=192.168.2.203 GATEWAY=192.168.2.1
** networking.sh dhcp fin.
configure files from Buffalo parameters.
Starting system logger: optarg:syslog
LoadConfFileString:key=[local_auth] not found in /etc/melco/info.
load_info ItemValue = off
LoadConfFileString:key=[ad_dns] not found in /etc/melco/info.
LoadConfFileOnOff:key=[info_visible] not found in /etc/melco/info.
LoadConfFileString:key=[usb_disk2] not found in /etc/melco/diskinfo.
Starting kernel logger:
Starting inetd:Starting kernelmon:#[miconapl.usb_set_power]
#[miconapl.fan_set_speed]
KERNELMOn (PSW_on)
XFS mounting filesystem sda6
/sbin/hotplug [block]
share
mkdir: Cannot create directory `/mnt/disk1/spool': File exists
mkdir: Cannot create directory `/mnt/disk1/spool/lp': File exists
mkdir: Cannot create directory `/mnt/disk1/spool/samba': File exists
mkdir: Cannot create directory `/mnt/disk1/spool/mac': File exists
** step3 **
KERNELMOn (lanact 0 half)
KERNELMOn (lanact 1000 full)
ftp is OFF
atalk is OFF
start
Starting HTTPD services: /usr/local/apache/bin/apachectl start: httpd started
configure samba
optarg:samba
LoadConfFileString:key=[local_auth] not found in /etc/melco/info.
load_info ItemValue = off
LoadConfFileString:key=[ad_dns] not found in /etc/melco/info.
LoadConfFileOnOff:key=[info_visible] not found in /etc/melco/info.
LoadConfFileString:key=[usb_disk2] not found in /etc/melco/diskinfo.
LoadConfFileString:key=[msdfs_link1_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link2_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link3_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link4_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link5_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link6_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link7_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link8_unc1] not found in /etc/melco/msdfs.
LoadConfFileString:key=[msdfs_link9_name] not found in /etc/melco/msdfs.
file:/etc/samba/smb.conf
>IconvCodeCharset CodePage=0,charset=CP932
file:/etc/pam_smb.conf
Setting up msdfs symbolic links... [Failed ]
Starting SMB services:
Starting NMB services:
Starting clientUtil_server:starting on eth0
Starting Bonjour services: done
Starting lsprcvd:Starting daemonwatch:codepage = CP932 (/etc/melco/info)
daemonwatch Ver.1.01
watch list file : /etc/daemonwatch.list
Start services: crond/dev/sda6 /mnt/disk1 xfs rw 0 0
#[miconapl.ups_linefail_off]
#[miconapl.ups_shutdown_on]
Starting pwrmgr:
Shutting down pwrmgr:
Starting pwrmgr:
** step4 **
Starting module subsystem ...
Starting module webaxs ... [Success.]
killall: mt-daapd: no process killed
web_root /usr/local/share/mt-daapd/admin-root
port 3689
admin_pw mt-daapd
#db_dir /var/cache/mt-daapd
#mp3_dir /mnt/mp3
#servername mt-daapd
runas nobody
playlist /etc/mt-daapd.playlist
#password mp3
extensions .mp3,.m4a,.m4p
#logfile /var/log/mt-daapd.log
#art_filename _folderOpenImage.jpg
#always_scan 0
#process_m3u 0
#scan_type 0
#compress 0
rescan_interval 3600
db_dir /mnt/disk1/mt-daapd
mp3_dir /mnt/disk1/share
servername LS-HGL487: LinkStation
Printer 'lp@localhost' - cannot open connection - No such file or directory
Make sure the remote host supports the LPD protocol
Printer 'lp-ps@localhost' - cannot open connection - No such file or directory
Make sure the remote host supports the LPD protocol
Start services: lpd
Starting services: rarpd tftpd rarpcfgd fwupdated.
route: SIOC[ADD|DEL]RT: No such process
killall: twonkymedia: no process killed
TwonkyMedia Version 4.4.4
/mnt/disk1#[miconapl.boot_end]
/etc/init.d/hdd_late_check.sh: line 6: /tmp/CheckDiskQueue: No such file or directory
Starting pid 1689, console /dev/ttyS0: '/sbin/getty'
BUFFALO INC. LinkStation series LS-HGL(SUININ)
LS-HGL487 login: root
root@LS-HGL487:~# exit
logout
Starting pid 1870, console /dev/ttyS0: '/sbin/getty'
BUFFALO INC. LinkStation series LS-HGL(SUININ)
LS-HGL487 login:
KERNELMOn (PSW_off)
CPU_STAT=normal_state
##### shutdown start
Starting pid 2189, console /dev/ttyS0: '/etc/init.d/rcDown'
--- rcDown ---
===== exec:shutdown_start.sh =====
called shutdown_start /etc/init.d/shutdown_start.sh
#[miconapl.bz_on]
#[miconapl.shutdown_wait]
===== exec:shutdown_proc.sh =====
KERNELMOn (PSW_off)
CPU_STAT=swpoff
Save current configuration files
delete unnecessary samba lock files on //etc/samba/lock...
tar: Removing leading `/' from member names
KERNELMOn (PSW_off)
tar: Removing leading `/' from member names
CPU_STAT=swpoff
Stop daemonwatch:done.
Stop logchkd:killall: logchkd: no process killed
done.
Stop lsprcvd:Stop services: crondStop inetd:done.
Stop errormon:killall: errormon: no process killed
done.
KERNELMOn (PSW_off)
CPU_STAT=swpoff
Stop clientUtil_server:rm: cannot remove `/var/run/clientUtil_server-eth0.pid': No such file or directory
Shutting down FTPD services: killall: proftpd: no process killed
Shutting down SMB services:
Shutting down NMB services:
Cleanup msdfs symbolic links... [Success]
Shutting down WINBIND services:
killall: winbindd: no process killed
Shutting down PAMSMBD services:
killall: pamsmbd: no process killed
KERNELMOn (PSW_off)
Stop servecies: atalkd afpd
/sbin/hotplug [module]
/sbin/hotplug [module]
/sbin/hotplug [module]
Can't unregister LS-HGL487:Workstation@*
Can't unregister LS-HGL487:netatalk@*
killall: atalkd: no process killed
killall: afpd: no process killed
CPU_STAT=swpoff
killall: papd: no process killed
KERNELMOn (PSW_off)
CPU_STAT=swpoff
KERNELMOn (PSW_off)
CPU_STAT=swpoff
Starting Bonjour services: done
stop
Shutting down HTTPD services: /usr/local/apache/bin/apachectl stop: httpd stopped
killall: speedy: no process killed
killall: speedy_backend: no process killed
KERNELMOn (PSW_off)
CPU_STAT=swpoff
Deconfiguration network interface: lo eth0
KERNELMOn (PSW_off)
CPU_STAT=swpoff
Stop kernelmon:killall: cat: no process killed
killall: /proc/buffalo/kernevnt: no process killed
done.
Shutting down kernel logger:
Shutting down system logger:
KERNELMOn (PSW_off)
CPU_STAT=swpoff
Stopping module subsystem ...
Shutting down webaxs ... [Failed. ]
Stop services: lpd
Printer 'lp@localhost' - cannot open connection - Connection refused
Make sure the remote host supports the LPD protocol
Printer 'lp-ps@localhost' - cannot open connection - Connection refused
Make sure the remote host supports the LPD protocol
/etc/init.d/shutdown_proc.sh: line 47: /etc/init.d/directcopy.sh: No such file or directory
Stop services: rarpd tftpd rarpcfgd fwupdated.
#[miconapl.fan_set_speed]
Stop errormon:killall: errormon: no process killed
done.
killall: apcupsd: no process killed
killall: omronupsd: no process killed
errormon ver.1.01(BuildDate Jan 25 2008 15:22:23 compiled for LS-HGL Series) Started
===== exec:umount_disk.sh =====
killing all servers..
Shutting down SMB services:
Shutting down NMB services:
Cleanup msdfs symbolic links... [Success]
Shutting down WINBIND services:
killall: winbindd: no process killed
Shutting down PAMSMBD services:
killall: pamsmbd: no process killed
Shutting down FTPD services: killall: proftpd: no process killed
Stop servecies: atalkd afpd
Can't unregister LS-HGL487:Workstation@*
Can't unregister LS-HGL487:netatalk@*
killall: atalkd: no process killed
killall: afpd: no process killed
killall: papd: no process killed
Starting Bonjour services: done
killing all daemons
Stop daemonwatch:done.
#[miconapl.fan_set_speed]
cat: /var/run/miconmon.pid: No such file or directory
kill: usage: kill [-s sigspec | -n signum | -sigspec] [pid | job]... or kill -l [sigspec]
killall: rsync: no process killed
stop
Shutting down HTTPD services: /usr/local/apache/bin/apachectl stop: httpd (no pid file) not running
killall: speedy: no process killed
killall: speedy_backend: no process killed
killall: sshd: no process killed
\n==== unmounting all disks ====
umount2: Invalid argument
umount: /mnt/usbdisk1: Illegal seek
/sbin/hotplug [block]
umount2: Invalid argument
umount: /mnt/usbdisk1: Illegal seek
/sbin/hotplug [block]
===== exec:sendsigs.sh =====
swapoff: /dev/sda5: Invalid argument
Shutting down kernel logger:
Shutting down system logger:
umount: /proc: device is busy
umount: /proc: device is busy
===== exec:errormon.sh =====
Stop errormon:done.
Starting pid 2841, console /dev/ttyS0: '/bin/umount'
The system is going down NOW !!
Sending SIGKILL to all processes.
The system is halted.
Synchronizing SCSI cache for disk sda:
System halted.
BuffaloChangePowerStatusBeforeHalt > Check power status. MagicKey = 2
BuffaloChangePowerStatusBeforeHalt > Changed to 122 from 2
Orion1 CPU = Low
> Checking hardware info ...
=== Strap status : 0x00800030 ===
=== H/W boardId : 0x23 ===
=== boardId : 0x1b ===
=== micon_support: off ===
> OK.
=== BUFFALO LS-HGL U-Boot. ===
** LOADER **
** BUFFALO BOARD: BUFFALO_BOARD_LS_HGL LE (CFG_ENV_ADDR=fffff000)
U-Boot 1.1.1 (Feb 4 2008 - 20:03:55) Marvell version: 1.12.1 - TINY
Buffalo Version: 1.13-1.00
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 400Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz
USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Using 88E1118 phy
buffalo_change_power_status > Read 0x7a
buffalo_IsStopAtUbootStatus > MagicKey=0x7a
buffalo_change_power_status > Read 0x7a
buffalo_change_power_status > Read 0x7a
buffalo_change_power_status > Writing 0x5c
Please Press HDD power button to continue ...
やはり System halted. では止まらない。
ヒョッとして、WOL できたりして。。。
Waiting for Magic Packet ?
|
|
← root のパスワードをつぶす / clear the root's password |
ハックの記録 LinkStation／玄箱 をハックしよう |
→ 新型 HS-DHGL でハック de 録!!（７）ファイルがなくなった番組をリストから消す |
