HS-DHGL のファームを玄箱/Pro で動かす

玄箱/Pro

カーネルだけではだめなら、、、
HS-DHGL 標準ファーム 1.03β2 をブートしてみる

接続

HS-DHGL 標準ファーム 1.03β2 をインストールした IDE HDD を フロント S-ATA ポートに接続。
景色は 3/5 とほぼ同じ

起動

bootcmd を書き換えて起動
Orion1   CPU =  Low

=== KURO U-Boot. ===
 ** LOADER **
 ** KUROBOX BOARD: KURO_BOX  LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (Feb 13 2007 - 15:59:43) Marvell version: 1.12.1 - TINY

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
NAND: 256 MB

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 500Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz


USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
<<system_bootend>>
Hit any key to stop autoboot:  0
Marvell>> setenv bootcmd 'ide reset; ext2load ide 1:1 $(default_kernel_addr) /$(kernel); bootm $(default_kernel_addr)'
Marvell>> boot

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
  Device 1: OK
Model: QUANTUM FIREBALLP AS20.5                 Firm: A1Y.1300 Ser#: 892034275708
            Type: Hard Disk
            Capacity: 19595.9 MB = 19.1 GB (40132503 x 512)

Using device ide1, partition 1

Loading from block device ide device 1, partition 1: Name: hdb1
  Type: U-Boot  File:/uImage.buffalo

1790940 bytes read
<<stop_sound>>
## Booting image at 00100000 ...
   Image Name:   Linux-2.6.12.6-arm1
   Created:      2006-10-04   4:37:49 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1790876 Bytes =  1.7 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

arg:console=ttyS0,115200 root=/dev/sda2 rw panic=5 BOOTVER=1.09
CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSGL ---
Uncompressing Linux.................................................................................................................... done, booting the kernel.
Linux version 2.6.12.6-arm1 (root@localhost.localdomain) (gcc version 3.4.4 (release) (CodeSourcery ARM 2005q3-2)) #79 Wed Oct 4 13:37:40 JST 2006
CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ)
CPU0: D VIVT write-back cache
CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets
Machine: MV-88fxx81
Using UBoot passing parameters structure
Sys Clk = 250000000, Tclk = 166664740


- Warning - This LSP release was tested only with U-Boot release 1.7.3

Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists
Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw panic=5 BOOTVER=1.09
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 128MB 0MB 0MB 0MB = 128MB total
Memory: 126080KB available (3066K code, 513K data, 112K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
FLASH boardId = 12
Flash bankwidth 1, base ff800000, size 400000
BUFFALO LS_GL FLASH size 4096[KB]

  Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_GL

 Detected Tclk 166664740 and SysClk 250000000
Marvell USB EHCI Host controller #0: c0503b00
Marvell USB EHCI Host controller #1: c0503a40
pexBarOverlapDetect: winNum 2 overlap current 0
mvPexInit:Warning :Bar 2 size is illigal
it will be disabled
please check Pex and CPU windows configuration
PCI: bus0: Fast back to back transfers enabled
PCI: bus1: Fast back to back transfers enabled
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
use IDMA acceleration in copy to/from user buffers. used channels 2 and 3
Done.
cesadev_init(c0011304)
mvCesaInit: sessions=640, queue=32, pSram=f0000000
Fast Floating Point Emulator V0.9 (c) Peter Teichmann.
SGI XFS with no debug enabled
Initializing Cryptographic API
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0x0 (irq = 3) is a 16550A
ttyS1 at MMIO 0x0 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
Marvell Gigabit Ethernet Driver 'egiga':
  o Ethernet descriptors in DRAM
  o DRAM SW cache-coherency
  o Checksum offload enabled
  o Loading network interface ** egiga_init_module (0)
'eth0'
Intergrated Sata device found
scsi0 : Marvell SCSI to SATA adapter
scsi1 : Marvell SCSI to SATA adapter
  Vendor: QUANTUM   Model: FIREBALLP AS20.5  Rev: A1Y.
  Type:   Direct-Access                      ANSI SCSI revision: 03
SCSI device sda: 40132503 512-byte hdwr sectors (20548 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 40132503 512-byte hdwr sectors (20548 MB)
SCSI device sda: drive cache: write back
 sda: sda1 sda2 sda4 < sda5 sda6 >
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi1, channel 0, id 0, lun 0,  type 0
physmap flash device: 400000 at ff800000
>jedec_probe
Found: SST 39LF020
phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank
number of JEDEC chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
cmdlinepart partition parsing not available
RedBoot partition parsing not available
ehci_platform ehci_platform.4523: EHCI Host Controller
ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1
ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000
ehci_platform ehci_platform.4523: park 0
ehci_platform ehci_platform.4523: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ehci_platform ehci_platform.16781: EHCI Host Controller
ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2
ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000
ehci_platform ehci_platform.16781: park 0
ehci_platform ehci_platform.16781: USB 0.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
USB Universal Host Controller Interface driver v2.2
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
MICON ctrl (C) BUFFALO INC. V.1.00 installed.
Kernel event proc (C) BUFFALO INC. V.1.00 installed.
MICON V2 (C) BUFFALO INC. V.1.00 installed.
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
> exit initrd_load
XFS mounting filesystem sda2
VFS: Mounted root (xfs filesystem).
Freeing init memory: 112K
init started:  BusyBox v1.1.1 (2006.08.08-01:53+0000) multi-call binary
Starting pid 218, console /dev/ttyS0: '/etc/init.d/rcS'
--- rcStart (hddroot) ---
Wed Mar 21 18:13:51 JST 2007
** step1 **
=====  exec:checkroot.sh  =====
mount: /dev/pts already mounted or /dev/pts busy
mount: according to mtab, devpts is already mounted on /dev/pts
mkdir: Cannot create directory `/var/lock': File exists
ln: /var/spool/cron/cron: File exists
rm: /var/lock/perfmon: is a directory
rm: /var/lock/printing: is a directory
rm: /var/lock/subsys: is a directory
Adding 125928k swap on /dev/ls_disk1_5.  Priority:-1 extents:1
=====  exec:create_devlink.sh  =====
=====  exec:procps.sh  =====
=====  exec:devpts.sh  =====
=====  exec:sethostname.sh  =====
configure files from Buffalo parameters.
=====  exec:restore_config.sh  =====
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: sda1: 1 orphan inode deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Update configuration files
Restore previous configuration files
** step2 **
=====  exec:networking.sh  =====
create network files..
IP=[dhcp], netmask=[], dgw=[], dns1=[], dns2=[]
killall: dhcpcd: no process killed
route: SIOC[ADD|DEL]RT: No such process
Configuration network interface: lo eth0
requesting DHCP  tout=30[s]
eth0: link down
eth0: link up<5>, full duplex<5>, speed 1 Gbps<5>
sendto:  count 1   sync 1
sendto:  count 0   sync 0
sendto:  count 1   sync 0
sendto:  count 1   sync 0
/etc/dhcpc/dhcpcd.exe ::: /etc/dhcpc/dhcpcd-eth0.info new
dhcpcd.exe: interface eth0 has been configured with new IP=192.168.1.40
configure files from Buffalo parameters.
=====  exec:syslog.sh  =====
Starting system logger:
Starting kernel logger:
=====  exec:inetd.sh  =====
Starting inetd:=====  exec:kernelmon.sh  =====
Starting kernelmon:=====  exec:miconmon.sh  =====
miconmon 1.00b3 started (Builddate May 27 2006 23:04:05)
=====  exec:mount_share.sh  =====
XFS mounting filesystem sda6
share
=====  exec:diskmon.sh  =====
diskmon ver.1.01
f_type=0x58465342
total_size=19704823808 free_byes=19656617984
=====  exec:errormon.sh  =====
Starting errormon:errormon ver.1.00b4(BuildDate Jun  7 2006 13:57:11) Started
=====  exec:hotplug.sh  =====
ls: /proc/scsi/usb-storage/: No such file or directory
=====  exec:ups  =====
** step3 **
=====  exec:micon_setup.sh  =====
f_type=0x58465342
total_size=19704823808 free_byes=19656617984
set_fan_speed_nonlinear>now_temperature=0[deg]
now_fanspeed=stop
set_fan_speed_nonlinear>setted_fanspeed=stop
f_type=0x58465342
total_size=19704823808 free_byes=19656617984
f_type=0x58465342
total_size=19704823808 free_byes=19656617984
f_type=0x58465342
total_size=19704823808 free_byes=19656617984
f_type=0x58465342
total_size=19704823808 free_byes=19656617984
f_type=0x58465342
total_size=19704823808 free_byes=19656617984
f_type=0x58465342
total_size=19704823808 free_byes=19656617984
f_type=0x58465342
total_size=19704823808 free_byes=19656617984
=====  exec:atalk.sh  =====
atalk is OFF
=====  exec:ftpd.sh  =====
ftp is OFF
=====  exec:httpd.sh  =====
start
Starting HTTPD services: /usr/local/apache/bin/apachectl start: httpd started

=====  exec:smb.sh  =====
Starting SMB services: configure samba
optarg:samba
LoadConfFileString:key=[ad_dns] not found in /etc/melco/info.
file:/etc/samba/smb.conf
file:/etc/pam_smb.conf

Starting NMB services: f_type=0x58465342
total_size=19704823808 free_byes=19656617984

=====  exec:pcastd.sh  =====
killall: chk_mediaserver.sh: no process killed
Start services: pcastd scheduler
mv7dxu2_d: module license 'Proprietary' taints kernel.
/sbin/hotplug [module]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [module]
/sbin/hotplug [module]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
pcastd 0.5.9  start.
key='server', value='on'
key='media', value='/mnt/disk1/share'
Set pcast_mp2000 seting media=global_param.public_root
key='usbdisk', value='1'
key='limit_media', value=''
key='limit_pass', value=''
EOF Detect.
config '/etc/pcast/pcastd.conf' open.
key='server_port', value='8000'
key='client_language_code', value='sjis'
key='skin_root', value='/etc/pcast/theme/pcast'
key='us_skin_root', value='/etc/pcast/theme_us/pcast'
key='flag_unknown_extention_file_hide', value='true'
key='flag_image_viewer', value='false'
key='flag_daemon', value='true'
key='flag_debug_log_output', value='false'
key='debug_log_filename', value='/mnt/disk1/_share/pcastd_debug.log'
EOF Detect.
Daemoning....
killall: mt-daapd: no process killed
Start services: mediaserver
Mediabolic Mediaserver
  Copyright: 1999-2005 Mediabolic, Inc.
  Version:   1.8.220
  Date:      Dec  5 2006 13:58:16

[18:15:39:879389] MSG [MAIN:784]: Mediabolic Build Configuration:
[18:15:39:880675] MSG [MAIN:784]:   clientlib: 1.8.225 Dec  5 2006 13:57:25 root@dd2-sugai GCC 3.4.4 serverupnpmsac:linux:mediabolic_d1:ja:BUFFALO:pcx
[18:15:39:889380] SYSTEM-INFO[MAIN:784]: Loading properties from: mediaserver.conf
[18:15:39:895061] Net Config-INFO[MAIN:784]: Set Net Config Defaults
[18:15:39:907104] LINUX_NETEVENT-ERR [MAIN:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:39:907451] LINUX_NETEVENT-WARN[MAIN:784]: flags2ifc: SIOCGMIIPHY if(eth0) (95:Operation not supported) -- Assuming 100mbps
[18:15:39:907820] LINUX_NETEVENT-ERR [MAIN:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:39:945779] STORMAN-INFO[MAIN:784]: Using media storage at '/mnt/disk1/mediaserver/data/media'
[18:15:39:946087] STORMAN-INFO[MAIN:784]: Real disk usage is currently: 11769 of 4810748 blocks - 0.24%
[18:15:39:946485] STORMAN-WARN[MAIN:784]: Need to load the persisted reservations!
[18:15:39:959944] MMSRV-INFO[MAIN:784]: Registering message handler for class [0x2]
[18:15:39:960177] MMSRV-INFO[MAIN:784]: Registering message handler for class [0x4]
[18:15:39:969044] CMANAGER-INFO[MAIN:784]: Verifier will run in 14400s
[18:15:39:969400] MMSRV-INFO[MAIN:784]: Registering message handler for class [0x5]
[18:15:39:972754] INFO[MAIN:784]: Initializing Music Library
[18:15:39:975040] MCONTENT_DB-INFO[MAIN:784]: Setting database cache size to 65536 bytes
[18:15:39:975601] RDB-MSG [MAIN:784]: rdb_init: Initializing redundant db with db_path [/mnt/disk1/mediaserver/data/db]
[18:15:40:048917] RDB-MSG [MAIN:784]: rdb_init: Redundant db recovered successfully
[18:15:40:049141] MCONTENT_DB-INFO[MAIN:784]: Opening databases from: /mnt/disk1/mediaserver/data/db
[18:15:40:062495] MCONTENT_DB-WARN[MAIN:784]: READ LAST ID: 1500
[18:15:40:062633] MCONTENT_DB-WARN[MAIN:784]: STORING BURN ID: 1600
[18:15:40:153395] MCONTENT_DB-WARN[MAIN:784]: SYNC -- KICKOFF THREAD
[18:15:40:154029] INFO[MAIN:784]: Initializing Photo Library
[18:15:40:154878] INFO[MAIN:784]: Initializing Video Library
[18:15:40:156597] MEDIASERVER-INFO[MAIN:784]: MWEB_MT server running on port: 58080
[18:15:40:157153] LINUX_NETEVENT-ERR [MAIN:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:40:158613] LINUX_NETEVENT-ERR [MAIN:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:40:159483] MMODULE_LINUX-INFO[MAIN:784]: Loading modules from: '/usr/lib/mediaserver/'
[18:15:40:182550] MMODULE_LINUX-INFO[MAIN:784]: Loading module: '/usr/lib/mediaserver/libmediabolic_format-en_us.so'
[18:15:40:201696] MMODULE_LINUX-INFO[MAIN:784]: Loading module: '/usr/lib/mediaserver/libmediabolic_format-ja.so'
[18:15:40:203904] MMODULE_LINUX-INFO[MAIN:784]: Loading module: '/usr/lib/mediaserver/libmediabolic_webui2-default.so'
[18:15:40:211942] MMODULE_LINUX-INFO[MAIN:784]: Loading module: '/usr/lib/mediaserver/libmediaserver_accesscontrol2.so'
[18:15:40:230786] MMODULE_LINUX-INFO[MAIN:784]: Loading module: '/usr/lib/mediaserver/libmediaserver_sync.so'
[18:15:40:265317] MMODULE_LINUX-INFO[MAIN:784]: Loading module: '/usr/lib/mediaserver/libmediaserver_upnp.so'
[18:15:40:300030] LINUX_NETEVENT-ERR [MAIN:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:40:720813] MMODULE_LINUX-INFO[MAIN:784]: Loading module: '/usr/lib/mediaserver/libmediaserver_upnpfilesys.so'
[18:15:40:731286] MMODULE_LINUX-INFO[MAIN:784]: Loading module: '/usr/lib/mediaserver/libmediaserver_upnpsync.so'
[18:15:40:734503] MMODULE_LINUX-INFO[MAIN:784]: Loading module: '/usr/lib/mediaserver/libmediaserver_webui2.so'
[18:15:40:744965] RDB-MSG [MAIN:784]: rdb_init: Initializing redundant db with db_path [/mnt/disk1/mediaserver/data/db/mediasets]
[18:15:40:747755] RDB-MSG [MAIN:784]: rdb_init: Redundant db recovered successfully
[18:15:40:763917] MACMEDIASETMANAGER-INFO[MAIN:784]: Opened media set DB with 65536-byte cache: /mnt/disk1/mediaserver/data/db/mediasets/mediasets
[18:15:40:781682] RDB-MSG [MAIN:784]: rdb_init: Initializing redundant db with db_path [/mnt/disk1/mediaserver/data/db/mpwq]
[18:15:40:800188] RDB-MSG [MAIN:784]: rdb_init: Redundant db recovered successfully
[18:15:40:811769] MPERSISTENTWORKQUEUE-INFO[MAIN:784]: Opened work queue DB with 65536-byte cache: /mnt/disk1/mediaserver/data/db/mpwq/maccesscontrol
[18:15:40:850668] MS-WEBUI2-INFO[MAIN:784]: Registering webui2 page handlers...
[18:15:40:851479] MEDIASERVER-INFO[MAIN:784]: Creating RTSP server on port 58080
[18:15:40:851630] MEDIASERVER-INFO[MAIN:784]: Diagnostics available at http://<ip>:58080/mdiag
[18:15:40:857316] IMSYNC-INFO[SYNC:784]:   registerListener took 0 milliseconds
[18:15:40:857554] IMSYNC-INFO[SYNC:784]: Registered new file for syncing: share/
[18:15:40:857967] IMSYNC-INFO[SYNC:784]: Changing sync state IMSYNC_STATE_STOPPED->IMSYNC_STATE_IDLE
[18:15:40:938796] LINUX_NETEVENT-ERR [MTP0:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:40:939234] LINUX_NETEVENT-ERR [MTP0:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:40:939577] LINUX_NETEVENT-ERR [MTP0:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:40:939923] LINUX_NETEVENT-ERR [MTP0:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:40:941624] UPNPDISC-WARN[MAIN:784]: ALIVE RESPONSE packet from 192.168.1.98:4 [upnp:rootdevice]
[18:15:40:945106] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:945502] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:945832] UPNPDISC-WARN[MAIN:784]: ALIVE RESPONSE packet from 192.168.1.98:4 [upnp:rootdevice]
[18:15:40:949031] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:949281] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:953910] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:954160] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:957517] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:957772] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:961974] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:962234] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:966319] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:966627] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:970039] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:973543] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:977522] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:977826] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:982153] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:982470] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:982919] LINUX_NETEVENT-ERR [MAIN:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:40:983288] LINUX_NETEVENT-ERR [MAIN:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:40:986708] LINUX_NETEVENT-ERR [MTP0:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:40:986992] LINUX_NETEVENT-ERR [MTP0:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:40:988476] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:988804] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:994355] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:994649] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:997907] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:998215] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:40:998678] LINUX_NETEVENT-ERR [MAIN:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:41:002377] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:41:002687] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:41:005952] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:41:006268] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:41:009564] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:41:009880] MUTIL_STRING-WARN[MAIN:784]: utf8_check(), Did not change CODE PAGE!
[18:15:41:023859] MMSRV-INFO[SYNC:784]: Registering message handler for class [0x20]
[18:15:41:024016] MMSRV-INFO[SYNC:784]: Registering message handler for class [0x4]
[18:15:41:025194] IMSYNC-INFO[MTP1:784]: Entering sync state IMSYNC_STATE_IDLE->IMSYNC_STATE_WORKING
[18:15:41:025467] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:025582] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:025684] LOW_MEM-WARN[MTP1:784]: --PREPARING HASH---
[18:15:41:025788] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:356473] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:358827] IMFILE_LINUX-ERR [FILESYSTEM:784]: MERROR_UNSUPP received at line 1253, in MgrPrv__addWatchNodesRecursive : imfile_linux.c
[18:15:41:358994] IMFILE_LINUX-WARN[FILESYSTEM:784]: Switching watch to polling: share/
[18:15:41:380296] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:380432] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:380533] LOW_MEM-WARN[MTP1:784]: --STARTING UPDATE--
[18:15:41:380636] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:380738] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:380870] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:380976] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:381077] LOW_MEM-WARN[MTP1:784]: --STARTING IMPORT--
[18:15:41:381179] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:381297] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:381400] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:381501] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:381603] LOW_MEM-WARN[MTP1:784]: ------FINISHED-----
[18:15:41:381706] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:381807] LOW_MEM-WARN[MTP1:784]: -------------------
[18:15:41:382272] IMSYNC-INFO[MTP1:784]: Exiting sync state IMSYNC_STATE_IDLE<-IMSYNC_STATE_WORKING
[18:15:42:086545] UPNPDISC-WARN[MAIN:784]: ALIVE RESPONSE packet from 192.168.1.40:27655 [upnp:rootdevice]
f_type=0x58465342
total_size=19704823808 free_byes=19656617984
[18:15:44:454654] LINUX_NETEVENT-ERR [MTP1:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:44:455015] LINUX_NETEVENT-ERR [MTP1:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:44:455403] UPNPSP-WARN[MTP1:784]: CHUNKED SOAP request!
[18:15:44:455962] UPNPSP-ERR [MTP1:784]: ****** INVALID CHUNKED SOAP REQUEST?!?!  DID HTTP_SERVER CHANGE? ******
[18:15:44:456180] UPNPSP-ERR [MTP1:784]: 00000000: 3c 73 3a 45 6e 76 65 6c 6f 70 65 20 78 6d 6c 6e   <s:Envelope xmln
[18:15:44:456318] UPNPSP-ERR [MTP1:784]: 00000010: 73 3a 73 3d 22 68 74 74 70 3a 2f 2f 73 63 68 65   s:s="http://sche
[18:15:44:456449] UPNPSP-ERR [MTP1:784]: 00000020: 6d 61 73 2e 78 6d 6c 73 6f 61 70 2e 6f 72 67 2f   mas.xmlsoap.org/
[18:15:44:456580] UPNPSP-ERR [MTP1:784]: 00000030: 73 6f 61 70 2f 65 6e 76 65 6c 6f 70 65 2f 22 20   soap/envelope/"
[18:15:44:456711] UPNPSP-ERR [MTP1:784]: 00000040: 73 3a 65 6e 63 6f 64 69 6e 67 53 74 79 6c 65 3d   s:encodingStyle=
[18:15:44:456843] UPNPSP-ERR [MTP1:784]: 00000050: 22 68 74 74 70 3a 2f 2f 73 63 68 65 6d 61 73 2e   "http://schemas.
[18:15:44:456973] UPNPSP-ERR [MTP1:784]: 00000060: 78 6d 6c 73 6f 61 70 2e 6f 72 67 2f 73 6f 61 70   xmlsoap.org/soap
[18:15:44:457104] UPNPSP-ERR [MTP1:784]: 00000070: 2f 65 6e 63 6f 64 69 6e 67 2f 22 3e 3c 73 3a 42   /encoding/"><s:B
[18:15:44:458291] SESSION_MAN-INFO[MTP1:784]: Checking authorizer for attach...
[18:15:44:458560] LINUX_NETEVENT-ERR [MTP1:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:44:459031] MACMEDIASETMANAGER-WARN[MTP1:784]: Principal already in set!
[18:15:44:459608] HTTP_SERVER-WARN[MTP1:784]: Probable reference leak -- Expected a req reference count of 2: 3
[18:15:44:469126] LINUX_NETEVENT-ERR [MTP0:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:44:469468] LINUX_NETEVENT-ERR [MTP0:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:44:469858] UPNPSP-WARN[MTP0:784]: CHUNKED SOAP request!
[18:15:44:470408] UPNPSP-ERR [MTP0:784]: ****** INVALID CHUNKED SOAP REQUEST?!?!  DID HTTP_SERVER CHANGE? ******
[18:15:44:470580] UPNPSP-ERR [MTP0:784]: 00000000: 3c 73 3a 45 6e 76 65 6c 6f 70 65 20 78 6d 6c 6e   <s:Envelope xmln
[18:15:44:470713] UPNPSP-ERR [MTP0:784]: 00000010: 73 3a 73 3d 22 68 74 74 70 3a 2f 2f 73 63 68 65   s:s="http://sche
[18:15:44:470844] UPNPSP-ERR [MTP0:784]: 00000020: 6d 61 73 2e 78 6d 6c 73 6f 61 70 2e 6f 72 67 2f   mas.xmlsoap.org/
[18:15:44:470975] UPNPSP-ERR [MTP0:784]: 00000030: 73 6f 61 70 2f 65 6e 76 65 6c 6f 70 65 2f 22 20   soap/envelope/"
[18:15:44:471104] UPNPSP-ERR [MTP0:784]: 00000040: 73 3a 65 6e 63 6f 64 69 6e 67 53 74 79 6c 65 3d   s:encodingStyle=
[18:15:44:471235] UPNPSP-ERR [MTP0:784]: 00000050: 22 68 74 74 70 3a 2f 2f 73 63 68 65 6d 61 73 2e   "http://schemas.
[18:15:44:471383] UPNPSP-ERR [MTP0:784]: 00000060: 78 6d 6c 73 6f 61 70 2e 6f 72 67 2f 73 6f 61 70   xmlsoap.org/soap
[18:15:44:471514] UPNPSP-ERR [MTP0:784]: 00000070: 2f 65 6e 63 6f 64 69 6e 67 2f 22 3e 3c 73 3a 42   /encoding/"><s:B
[18:15:44:472322] SESSION_MAN-INFO[MTP0:784]: Checking authorizer for attach...
[18:15:44:472591] LINUX_NETEVENT-ERR [MTP0:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:44:473005] MACMEDIASETMANAGER-WARN[MTP0:784]: Principal already in set!
[18:15:44:473523] HTTP_SERVER-WARN[MTP0:784]: Probable reference leak -- Expected a req reference count of 2: 3
[18:15:44:482654] LINUX_NETEVENT-ERR [MTP2:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:44:482991] LINUX_NETEVENT-ERR [MTP2:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:44:483295] HTTP_SERVER-WARN[MTP2:784]: No registered protocol handler '/ HTTP/1.1'
[18:15:44:483512] UPNPSP-WARN[MTP2:784]: CHUNKED SOAP request!
[18:15:44:484116] UPNPSP-ERR [MTP2:784]: ****** INVALID CHUNKED SOAP REQUEST?!?!  DID HTTP_SERVER CHANGE? ******
[18:15:44:815735] UPNPSP-ERR [MTP2:784]: 00000000: 3c 73 3a 45 6e 76 65 6c 6f 70 65 20 78 6d 6c 6e   <s:Envelope xmln
[18:15:44:815897] UPNPSP-ERR [MTP2:784]: 00000010: 73 3a 73 3d 22 68 74 74 70 3a 2f 2f 73 63 68 65   s:s="http://sche
[18:15:44:816030] UPNPSP-ERR [MTP2:784]: 00000020: 6d 61 73 2e 78 6d 6c 73 6f 61 70 2e 6f 72 67 2f   mas.xmlsoap.org/
[18:15:44:816160] UPNPSP-ERR [MTP2:784]: 00000030: 73 6f 61 70 2f 65 6e 76 65 6c 6f 70 65 2f 22 20   soap/envelope/"
[18:15:44:816291] UPNPSP-ERR [MTP2:784]: 00000040: 73 3a 65 6e 63 6f 64 69 6e 67 53 74 79 6c 65 3d   s:encodingStyle=
[18:15:44:816422] UPNPSP-ERR [MTP2:784]: 00000050: 22 68 74 74 70 3a 2f 2f 73 63 68 65 6d 61 73 2e   "http://schemas.
[18:15:44:816552] UPNPSP-ERR [MTP2:784]: 00000060: 78 6d 6c 73 6f 61 70 2e 6f 72 67 2f 73 6f 61 70   xmlsoap.org/soap
[18:15:44:816683] UPNPSP-ERR [MTP2:784]: 00000070: 2f 65 6e 63 6f 64 69 6e 67 2f 22 3e 3c 73 3a 42   /encoding/"><s:B
[18:15:44:817091] SESSION_MAN-INFO[MTP2:784]: Checking authorizer for attach...
[18:15:44:817340] LINUX_NETEVENT-ERR [MTP2:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
=====  exec:epg.sh  =====
[18:15:44:819254] LINUX_NETEVENT-ERR [MTP3:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:44:819641] LINUX_NETEVENT-ERR [MTP3:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:44:830479] UPNPSP-WARN[MTP3:784]: CHUNKED SOAP request!
[18:15:44:830747] UPNPSP-ERR [MTP3:784]: ****** INVALID CHUNKED SOAP REQUEST?!?!  DID HTTP_SERVER CHANGE? ******
[18:15:44:830897] UPNPSP-ERR [MTP3:784]: 00000000: 3c 73 3a 45 6e 76 65 6c 6f 70 65 20 78 6d 6c 6e   <s:Envelope xmln
[18:15:44:831029] UPNPSP-ERR [MTP3:784]: 00000010: 73 3a 73 3d 22 68 74 74 70 3a 2f 2f 73 63 68 65   s:s="http://sche
[18:15:44:831162] UPNPSP-ERR [MTP3:784]: 00000020: 6d 61 73 2e 78 6d 6c 73 6f 61 70 2e 6f 72 67 2f   mas.xmlsoap.org/
[18:15:44:831293] UPNPSP-ERR [MTP3:784]: 00000030: 73 6f 61 70 2f 65 6e 76 65 6c 6f 70 65 2f 22 20   soap/envelope/"
[18:15:44:831424] UPNPSP-ERR [MTP3:784]: 00000040: 73 3a 65 6e 63 6f 64 69 6e 67 53 74 79 6c 65 3d   s:encodingStyle=
[18:15:44:831556] UPNPSP-ERR [MTP3:784]: 00000050: 22 68 74 74 70 3a 2f 2f 73 63 68 65 6d 61 73 2e   "http://schemas.
[18:15:44:831688] UPNPSP-ERR [MTP3:784]: 00000060: 78 6d 6c 73 6f 61 70 2e 6f 72 67 2f 73 6f 61 70   xmlsoap.org/soap
[18:15:44:831819] UPNPSP-ERR [MTP3:784]: 00000070: 2f 65 6e 63 6f 64 69 6e 67 2f 22 3e 3c 73 3a 42   /encoding/"><s:B
[18:15:44:832220] SESSION_MAN-INFO[MTP3:784]: Checking authorizer for attach...
[18:15:44:832466] LINUX_NETEVENT-ERR [MTP3:784]: do_wireless_ioctl: if(eth0:eth0) ioctl(35585:SIOCGIWNAME) (22:Invalid argument)
[18:15:44:840253] RDB-MSG [MTP2:784]: stabilize_db_group
[18:15:44:849656] UPNPSP-WARN[MTP2:784]: Control request [SetDefaultMediaSet] took 360 milliseconds to answer!
[18:15:44:849808] HTTP_SERVER-WARN[MTP2:784]: Probable reference leak -- Expected a req reference count of 2: 3
[18:15:44:850133] MACMEDIASETITERS-WARN[MTP3:784]: End of iteration! (No further elements)
[18:15:44:850630] UPNPSP-WARN[MTP3:784]: Control request [GetMediaSets] took 40 milliseconds to answer!
[18:15:44:850770] HTTP_SERVER-WARN[MTP3:784]: Probable reference leak -- Expected a req reference count of 2: 3
Start services: EPGd iRCommander
EPGd : version 1.1.0
0.2.0
=====  exec:directcopy.sh  =====
Start services: DirectCopy
=====  exec:clientUtil_servd.sh  =====
Starting clientUtil_server:starting on eth0
=====  exec:lsprcvd.sh  =====
Starting lsprcvd:=====  exec:daemonwatch.sh  =====
Starting daemonwatch:watch list file : /etc/daemonwatch.list
=====  exec:cron.sh  =====
Start services: crond=====  exec:ltbootd.sh  =====
Starting services: rarpd tftpd rarpcfgd fwupdated.
=====  exec:logchkd.sh  =====
Starting logchkd:logchkd ver.1.00(Aug  8 2006) started
=====  exec:bootcomplete.sh  =====
>MiconCommon_Constructor
set_fan_speed_nonlinear>now_temperature=0[deg]
now_fanspeed=stop
set_fan_speed_nonlinear>setted_fanspeed=stop
f_type=0x58465342
total_size=19704823808 free_byes=19656617984
>MiconCommon_Constructor
err: RecvPacket: readlen=0.
Starting pid 1127, console /dev/ttyS0: '/sbin/getty'

BUFFALO INC. LinkStation series HS-DHGL(JINMU)
HS-DHGL276 login:
立ち上がることは立ち上がったが、なんだかエラーいっぱい

電源ボタン

電源ボタン長押し、、、、効かない。

shutdown

HS-DHGL276 login: root
Password:
root@HS-DHGL276:~# shutdown -h now
Starting pid 1584, console /dev/ttyS0: '/etc/init.d/rcDown'
root@HS-DHGL276:~# --- rcDown ---
=====  exec:shutdown_start.sh  =====
called shutdown_start /etc/init.d/shutdown_start.sh
>MiconCommon_Constructor
err: RecvPacket: readlen=0.
>MiconCommon_Constructor
err: RecvPacket: readlen=0.
=====  exec:shutdown_proc.sh  =====
Stop logchkd:done.
Stop services: crondStop services: rarpd tftpd rarpcfgd fwupdated.
Stop daemonwatch:done.
Stop servecies: atalkd afpd
/sbin/hotplug [module]
/sbin/hotplug [module]
/sbin/hotplug [module]
Can't unregister HS-DHGL276:Workstation@*
Can't unregister HS-DHGL276:netatalk@*
killall: atalkd: no process killed
killall: afpd: no process killed
killall: papd: no process killed
/sbin/hotplug [module]
ERROR: Module p8022 does not exist in /proc/modules
/sbin/hotplug [module]
/sbin/hotplug [module]
Stop lsprcvd:/etc/init.d/shutdown_proc.sh: line 9: /etc/init.d/clientUtil_server.sh: No such file or directory
Shutting down FTPD services: killall: proftpd: no process killed


stop
Shutting down HTTPD services: /usr/local/apache/bin/apachectl stop: httpd stopped

Shutting down SMB services:
Shutting down NMB services:
Shutting down WINBIND services: killall: winbindd: no process killed

Shutting down PAMSMBD services: killall: pamsmbd: no process killed

Stop services: pcastd scheduler
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [module]
/sbin/hotplug [module]
/sbin/hotplug [class]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
/sbin/hotplug [drivers]
/sbin/hotplug [module]
Stop services: mediaserver
1
2
3
4
5
6
7
8
9
10
Stop services: EPGd iRCommander
Stop services: DirectCopy
Deconfiguration network interface: lo eth0
killall: dhcpcd: no process killed
Stop inetd:done.
Stop kernelmon:done.
Stop errormon:done.
Save current configuration files
tar: Removing leading '/' from member names
tar: Removing leading '/' from member names
Stop logchkd:done.
=====  exec:umount_disk.sh  =====
killing all servers..
Shutting down SMB services:
Shutting down NMB services:
Shutting down WINBIND services: killall: winbindd: no process killed

Shutting down PAMSMBD services: killall: pamsmbd: no process killed

Shutting down FTPD services: killall: proftpd: no process killed


Stop servecies: atalkd afpd
/sbin/hotplug [module]
/sbin/hotplug [module]
/sbin/hotplug [module]
Can't unregister HS-DHGL276:Workstation@*
Can't unregister HS-DHGL276:netatalk@*
killall: atalkd: no process killed
killall: afpd: no process killed
killall: papd: no process killed
/sbin/hotplug [module]
ERROR: Module p8022 does not exist in /proc/modules
/sbin/hotplug [module]
/sbin/hotplug [module]
killing all daemons
Stop daemonwatch:done.
killall: rsync: no process killed
stop
Shutting down HTTPD services: /usr/local/apache/bin/apachectl stop: httpd (no pid file) not running

killall: sshd: no process killed
\n==== unmounting all disks ====
umount2: Invalid argument
umount: /mnt/usbdisk1: Illegal seek
umount2: Invalid argument
umount: /mnt/usbdisk2: not mounted
umount: /dev/usbdisk1_1: not found
umount: /dev/usbdisk2_1: not found
=====  exec:sendsigs.sh  =====
Shutting down kernel logger:
Shutting down system logger:
umount: /: device is busy
umount: /: device is busy
umount: /: device is busy
Starting pid 2271, console /dev/ttyS0: '/bin/umount'
umount: /: device is busy
umount: /: device is busy
umount: /: device is busy
The system is going down NOW !!
Sending SIGTERM to all processes.
The system is halted.
Synchronizing SCSI cache for disk sda:
System halted.
>miconCntl_PowerOff
>miconCntl_ShutdownWait
落ちるのは落ちた。

予想に反して、そのままではまともに動きそうにない。




KURO-BOX/PRO
玄人志向
楽天市場
TSUKUMO ネットショップ
Yahoo!ショッピング
Sofmap
クレバリー
TwoTop New!


HS-DHGL のカーネルを玄箱/Pro で動かす(2)
ハックの記録
LinkStation/玄箱 をハックしよう

「玄箱/Pro をハックしよう」ページ開設

Copyright (C) 2003-2007 Yasunari Yamashita. All Rights Reserved.
yasunari @ yamasita.jp 山下康成@京都府向日市