HDD boot モードの U-Boot 環境/the U-Boot environment at HDD boot mode.

Orion1   CPU =  Low

=== KURO U-Boot. ===
 ** LOADER **
 ** KUROBOX BOARD: KURO_BOX  LE (CFG_ENV_ADDR=fffff000)


U-Boot 1.1.1 (Feb 13 2007 - 15:59:43) Marvell version: 1.12.1 - TINY

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB
[256kB@fffc0000] Flash: 256 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
NAND: 256 MB

Soc: 88F5182 A2
CPU: ARM926 (Rev 0) running @ 500Mhz
Orion 1 streaming disabled
SysClock = 250Mhz , TClock = 166Mhz


USB 0: host mode
USB 1: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Using 88E1118 phy
hit any key to switch tftp boot.
Hit any key to stop autoboot:  0
<<system_bootend>>
Hit any key to stop autoboot:  0
Marvell>> printenv
baudrate=115200
loads_echo=0
ipaddr=192.168.11.150
serverip=192.168.11.1
rootpath=/nfs/arm
cpuName=926
CASset=min
MALLOC_len=4
bootargs_end=:::DB88FXX81:eth0:none
ethact=egiga0
ethaddr=00:16:01:A4:CA:A5
buffalo_ver=BOOTVER=1.091
build_time=15:59:38
initrd=initrd.buffalo
kernel=uImage.buffalo
nand_uImage_offset=20000
default_initrd_addr=0x02000000
def_tftp=tftp $(default_kernel_addr) $(kernel); tftp $(default_initrd_addr) $(initrd); setenv bootargs $(bootargs_base) $(bootargs_root)  rw initrd=0x02000040,20M panic=5 $(buffalo_ver); bootm $(default_kernel_addr) $(default_initrd_addr)
default_kernel_addr=0x00100000
bootargs_base=console=ttyS0,115200
bootargs_root=root=/dev/sda2 rw panic=5
bootargs=console=ttyS0,115200 root=/dev/sda2 rw panic=5 BOOTVER=1.09
bootcmd=ide reset; ext2load ide 0:1 $(default_kernel_addr) /$(kernel); bootm $(default_kernel_addr)
nand_boot=no
stdin=serial
stdout=serial
stderr=serial
enaMonExt=no
enaFlashBuf=yes
enaCpuStream=no
ethprime=egiga0
bootdelay=3
disaMvPnp=no
overEthAddr=no
usb0Mode=host
usb1Mode=host

Environment size: 1046/4092 bytes
Marvell>>

bootargs_root=root=/dev/mtdblock2 rw panic=5
bootargs=$(bootargs_base) $(bootargs_root) $(buffalo_ver)
bootcmd=nboot $(default_kernel_addr)  0 $(nand_uImage_offset) ;setenv bootargs $(bootargs_base) $(bootargs_root) $(buffalo_ver); bootm $(default_kernel_addr)
nand_boot=yes

製品仕様書の記述とは微妙に異なる。
There is a few difference from the product specification.

KURO-BOX/PRO

玄人志向 楽天市場 TSUKUMO ネットショップ Yahoo!ショッピング Sofmap クレバリー TwoTop

SCON-KIT/PRO

玄人志向 TSUKUMO ネットショップ Yahoo! ショッピング パソＱ ValuMore uWorks

玄箱PROをハックしよう

ASCII 楽天ブックス Amazon cbook24 e-hon JBook BK1 livedoorブックス 紀伊國屋書店BookWeb